Cylinder with Lock Series CNS Contents 125 CS1N125A-PS Set of above nos. $6, $8, $9, %3, %4, %7 140 DCS1N140A-PS 160 CS1N160A-PS -X Since the lock section for Series CNS is normally replaced as a unit, kits are for the cylinder section only. These can be ordered using the order number for each bore size. Seal kit includes $6, $8, $9, %3, %4, %7. Order the seal kit, based on each bore size.
Y 2-4-139 VQ1000/2000 Kit (Flat ribbon cable connector) J VQ1000 The broken lines indicate the DIN rail mounting style [-D] and the side entry connection [-PS].
Top/vertical entry connector for FU and PU while side (horizontal) entry connector for FS and PS. Note 2) VQ5
In addition, in the case of trouble, please send it back to the supplier for repair or replacement. 10 VFR3000-OMH0005-B S Revision history A Renewal MZ B Safety Instructions PS 1st printing: AW 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com Note: Specifications are subject to change without prior notice and any
(Ps) (MPa) 6 Stop the slide block using the external stopper 0.55 10 When stopping a load in mid-stroke using an 15 external stopper, adjustment bolt or bumper bolt, 20 operate within the operating pressure limits shown 0.65 25 in the table 10.
Simple Pressure Vessels Directive This directive is applied to welded vessels whose maximum operating pressure (PS) and volume of vessel (V) exceed 50 bar/L. Such vessels require EC type examination and then CE marking. 15-18-6 SMC Product Conforming to International Standards national Standards you to comply with EC directives and CSA/UL standards.
Top/vertical entry connector for FU and PU while side (horizontal) entry connector for FS and PS.
(Heat source) TS Level switch Temperature sensor (For compressor discharge) Fluid level indicator Pressure sensor (For low-pressure refrigerant gas) PS PS TS Temperature sensor (For discharge) Temperature sensor (For compressor intake) Compressor Pressure sensor (For discharge) Circulating fluid outlet TS Circulating fluid circuit Refrigeration circuit Drain port Refrigeration circuit Circulating
Indicator Unit (LED) Description and Its Function SI unit (DeviceNet) SI unit (PROFIBUS-DP) Input block 1 3 5 7 PWR 0 2 4 6 TM TM PWR(V) RUN PWR(V) MOD/NET PWR ADDRESS 1 H L 0 SETTINGS DIA BF FB FB PS PS Description Description Function Function Description Function PWR(V) ON when solenoid valve power supply is turned ON. ON when sensor power is turned ON.
Contents 30 Damper B 20 Urethane CG1N20-PS 40 is the same as damper A 31 Snap ring 25 Stainless steel CG1N25-PS 32 A set of above Nos. Wear ring 32 Resin CG1N32-PS 33 37, 39, 40 Rod end nut 40 Rolled steel CG1N40-PS Nickel plated 34 BC element Bronze 35 Since the lock section for Series CNG is normally replaced as a unit, replacement seal kits are for the cylinder section only.
Contents Basic internal retaining ring MUB32-PS qPiston seal wRod seal eBumper Seal kit includes q, w, e. Since the seal kit does not include a grease pack, order the Grease Pack below separately. CLKU cannot be disassembled and therefore no seal kit is available. LGrease Pack Kit no.
Simple Pressure Vessels Directive This directive is applied to welded vessels whose maximum operating pressure (PS) and volume of vessel (V) exceed 50 bar/L. Such vessels require EC type examination and then CE marking. 14-21-6 SMC Product Conforming to International Standards national Standards you to comply with EC directives and CSA/UL standards.
Simple Pressure Vessels Directive This directive is applied to welded vessels whose maximum operating pressure (PS) and volume of vessel (V) exceed 50 bar/L. Such vessels require EC type examination and then CE marking. 15-18-6 SMC Product Conforming to International Standards national Standards you to comply with EC directives and CSA/UL standards.
Simple Pressure Vessels Directive This directive is applied to welded vessels whose maximum operating pressure (PS) and volume of vessel (V) exceed 50 bar/L. Such vessels require EC type examination and then CE marking. 15-18-6 SMC Product Conforming to International Standards national Standards you to comply with EC directives and CSA/UL standards.
Simple Pressure Vessels Directive This directive is applied to welded vessels whose maximum operating pressure (PS) and volume of vessel (V) exceed 50 bar/L. Such vessels require EC type examination and then CE marking. 14-21-6 SMC Product Conforming to International Standards national Standards you to comply with EC directives and CSA/UL standards.
Plug-in Connector connection PS port: Pressure detection port (M5 x 0.8) Filter Eliminates foreign matter on vacuum and release side.
V Ps + 0.1 293 S = 12.1 log10 () (6) t P + 0.1 T S : Effective area [mm2] V : Air tank capacity [dm3] t : Discharging time [s] Ps : Pressure inside air tank before discharging [MPa] P : Residual pressure inside air tank after discharging [MPa] T : Temperature inside air tank before discharging [K] Power supply Thermometer Pressure switch Control circuit Solenoid valve Pressure control equipment
r6 on "A" pllot: mhu510 {0.09 (0.89) {0.69) 125 PS|G I .3Kgl/cmr) M6)dmum Ambl6nt T6moraturt I 140. F (60. C) Msdra: Alr 0ubrlcted or oll lr3), any non.flammsbtG, non.lorlc, non{ollo3iva oasE oxcol oxvo6r,.
Simple Pressure Vessels Directive This directive is applied to welded vessels whose maximum operating pressure (PS) and volume of vessel (V) exceed 50 bar/L. Such vessels require EC type examination and then CE marking. 14-21-6 SMC Product Conforming to International Standards national Standards you to comply with EC directives and CSA/UL standards.
Simple Pressure Vessels Directive This directive is applied to welded vessels whose maximum operating pressure (PS) and volume of vessel (V) exceed 50 bar/L. Such vessels require EC type examination and then CE marking. 15-18-6 SMC Product Conforming to International Standards national Standards you to comply with EC directives and CSA/UL standards.