Fieldbus system EtherCAT compatible SI Unit Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set with wet hands. This may lead to an electric shock. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set with wet hands. This may lead to an electric shock. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set with wet hands. This may lead to an electric shock. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Do not operate in locations where vibration or shock will occur. 4. Do not operate in a location near a heat source or where radiated heat will be received. 16 Series AS-FG/ASD-FG Specific Product Precautions Be sure to read before handling. Refer to pages 15 and 16 for safety instructions and flow control equipment precautions.
Do not make any modifications to be product. Do not take the product apart. Piping Caution 1. Before piping Make sure that all debris, cutting oil, dust, etc, are removed from the piping. 2. Wrapping of pipe tape When screwing piping or fittings into ports, ensure that chips from the pipe threads or sealing material do not get inside the piping.
SOL.a Station 2 14 Station 1 SOL.b 14 1 SOL.a Station 1 1 SOL.a Station 1 SOL.a 1 The common polarity should be the same as the common specifications of the valve to be used.
Q ZP T 10 06 31.8 10 6 4.5 08 35.9 14 8 6 20 30 50 40 50 A14 06 19.9 12 6 3 08 24.9 14 8 Width across flats P N N Dimensions Per Vacuum Inlet: Barb Fitting Model N P Fitting part min. hole size Vacuum inlet direction q Pad dia.
It will cause failure of the driver or its peripheral devices. 14. Do not use the product in an environment subject to a 5. If a danger against the personnel is expected due to an temperature cycle.
Do not Do not use in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. The product is not designed to be explosion proof. Do not Do not use the product in a place where static electricity is a problem. Otherwise failure or malfunction of the system can result.
The received message is deleted if the calculation result and received CRC do not match.
Do not cut the cable. b. Keep the minimum bend radius of the cable. c. Do not tighten the cable too much by tying band. Do not deform the cable by placing object on the cable. d. Avoid the factor of cable runaway such as cable duct. e. Do not twist or damage to the cable.
Do not Do not operate the product outside of the specifications. Do not use the product with flammable or harmful fluids. Fire, malfunction, or damage to the product may result. Check the specifications before use. Do not Do not use in an atmosphere containing flammable or explosive gases. Fire or an explosion may result. This product is not explosion-protected.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set up with wet hands. An electric shock can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Refer to LECSA Operation Manual (Simplified Edition),section 3.2.1 (2) and (3) for input/output signal details. 14 - 3.2.5 Source I/O interfaces Source type I/O interfaces can be used with this driver. If used, all DI-1 input signals and DO-1 output signals are source type signals.
SUP 1/8 11 (0.60) 10 (0.54) VHS20 1/8 1/4 16 (0.87) 14 (0.76) 1/4 14 (0.76) 16 (0.87) VHS30 OUT IN 1/4 3/8 29 (1.57) 31 (1.68) 1/4 36 (1.95) 27 (1.46) B 3/8 VHS40 3/8 40 (2.17) 38 (2.06) 1/2 42 (2.28) 55 (2.98) Note) Use an air filter on the IN side for operating protection. EXH.
MK/MK2 RSQ/RSG RSH q Do not operate the cylinder horizontally. w Do not perform work in the rotational direction. CE1 CE2 ML2B ML1C REA REC Figure 3 Figure 4 RHC e Do not clamp during a rotational stroke. MTS CC Figure 5 t Make sure that the workpiece does not move during clamping. r Do not clamp on a slanted surface.
Do not apply torque at other points as the product may be damaged. Rotate body A manually for positioning after installation. 12. Do not use body A and/or elbow body for applications involving continuous rotation. Mounting Body A and the fitting section may be damaged. Warning 1.
Do not apply torque at other points as the product may be damaged. Rotate body A manually for positioning after installation. 12. Do not use body A and/or elbow body for applications involving continuous rotation. Mounting Body A and the fitting section may be damaged. Warning 1.
material 1 Resin Refer to . on page 14 for replacement parts. 10 Sound absorbing material 2 Resin 11 Valve plate PBT Specific Product Precautions Refer to m on page 14 for replacement parts. 12 Knob POM 13 Needle Brass (Electroless nickel plating) 14 Port block assembly Aluminum alloy/NBR/Stainless steel Refer to b on page 14 for replacement parts. 15 Supply valve, Release valve Refer to
Do not apply impact/collision/resistance for mover of actuator in operation. It will cause decrease of products life, damage to product, and so on. [Ground] Warning 1. Please do the earth construction surely. 2. Please refer to the driver manual for the grounding procedure and notes. [Unpackaging] Caution 1.