Electric Actuator with Integrated Guide Series LTF Series LTF Lead screw lead mm Mounting Series Guide type Motor type Model Page orientation Ground ball screw Rolled ball screw 6 10 6 10 LTF6 Page 60 to Horizontal 10 20 10 20 LTF8 Page 68 to Frame-type It will cause failure of the driver or its peripheral devices. 14. Do not use the product in an environment subject to a 5. If a danger against the personnel is expected due to an temperature cycle.
Do not Do not use in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. The product is not designed to be explosion proof. Do not Do not use the product in a place where static electricity is a problem. Otherwise failure or malfunction of the system can result.
The received message is deleted if the calculation result and received CRC do not match.
Do not cut the cable. b. Keep the minimum bend radius of the cable. c. Do not tighten the cable too much by tying band. Do not deform the cable by placing object on the cable. d. Avoid the factor of cable runaway such as cable duct. e. Do not twist or damage to the cable.
Do not Do not operate the product outside of the specifications. Do not use the product with flammable or harmful fluids. Fire, malfunction, or damage to the product may result. Check the specifications before use. Do not Do not use in an atmosphere containing flammable or explosive gases. Fire or an explosion may result. This product is not explosion-protected.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set up with wet hands. An electric shock can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Refer to LECSA Operation Manual (Simplified Edition),section 3.2.1 (2) and (3) for input/output signal details. 14 - 3.2.5 Source I/O interfaces Source type I/O interfaces can be used with this driver. If used, all DI-1 input signals and DO-1 output signals are source type signals.
SUP 1/8 11 (0.60) 10 (0.54) VHS20 1/8 1/4 16 (0.87) 14 (0.76) 1/4 14 (0.76) 16 (0.87) VHS30 OUT IN 1/4 3/8 29 (1.57) 31 (1.68) 1/4 36 (1.95) 27 (1.46) B 3/8 VHS40 3/8 40 (2.17) 38 (2.06) 1/2 42 (2.28) 55 (2.98) Note) Use an air filter on the IN side for operating protection. EXH.
MK/MK2 RSQ/RSG RSH q Do not operate the cylinder horizontally. w Do not perform work in the rotational direction. CE1 CE2 ML2B ML1C REA REC Figure 3 Figure 4 RHC e Do not clamp during a rotational stroke. MTS CC Figure 5 t Make sure that the workpiece does not move during clamping. r Do not clamp on a slanted surface.
Do not apply torque at other points as the product may be damaged. Rotate body A manually for positioning after installation. 12. Do not use body A and/or elbow body for applications involving continuous rotation. Mounting Body A and the fitting section may be damaged. Warning 1.
Do not apply torque at other points as the product may be damaged. Rotate body A manually for positioning after installation. 12. Do not use body A and/or elbow body for applications involving continuous rotation. Mounting Body A and the fitting section may be damaged. Warning 1.
material 1 Resin Refer to . on page 14 for replacement parts. 10 Sound absorbing material 2 Resin 11 Valve plate PBT Specific Product Precautions Refer to m on page 14 for replacement parts. 12 Knob POM 13 Needle Brass (Electroless nickel plating) 14 Port block assembly Aluminum alloy/NBR/Stainless steel Refer to b on page 14 for replacement parts. 15 Supply valve, Release valve Refer to
Do not apply impact/collision/resistance for mover of actuator in operation. It will cause decrease of products life, damage to product, and so on. [Ground] Warning 1. Please do the earth construction surely. 2. Please refer to the driver manual for the grounding procedure and notes. [Unpackaging] Caution 1.
(Refer to "Mounting and Installation" on page 14.) Do not apply excessive stress to the product when it is mounted with a panel mount. Otherwise damage to the product and disconnection from the panel mount can result. Be sure to ground terminal FG when using a commercially available switch-mode power supply. Do not drop, hit or apply shock to the Pressure switch.
Precautions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set with wet hands. This may lead to an electric shock. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Fig. 2 Center of gravity of the load mounted to the rod end Do not scratch or dent the sliding parts of the piston rod. Damage to the seals may lead to air leakage and locking failure. Do not apply loads with impact, strong vibration or rotational force while the lock mechanism is activated.
50 97 69 20 16 12 64 14 11 148 M8 32 32 46 M10 x 1.5 22 M10 x 1.5 8.6 14 9 Rc1/4 NPT1/4 G1/4 63 102 74 20 16 12 78 16.5 13.5 162 M10 39 39 58 M10 x 1.5 22 M10 x 1.5 8.6 14 9 Rc1/4 NPT1/4 G1/4 MGF MGZ Bore size [mm] PA PB PW Q R S T U VA VB WA WB X XA XB XC XL YY YL Z 75 st or less Over 75 st to 175 st Over 175 st to 250 st Over 250 st 75 st or less Over 75 st to 175 st Over 175 st to 250
Rear Clevis/Male (1.5 to 14) L MS1 Foot Mount (1.5 to 14) S MS2 Side Lug (1.5 to 14) O MS3 Centerline Lug (1.5 to 14) R MS4 Side-Tapped (1.5 to 14) P .MS7 Front Lug Mount (1.5 to 14) J MT2 Cap Trunnion (1.5 to 14) U MT1 Head Trunnion (1.5 to 14) T MT4 Center Trunnion (1.5 to 14) *See below B MX0 Basic/No Mount (1.5 to 14) BA .
(1) Do not use this positioner out of the range of its specifications as this can cause failure. (Refer to 1.
Do not scratch the sliding surface of the shock absorbers piston rod. This can cause a loss of durability and return malfunction. D-X Do not turn bottom screw Piston rod Individual -X Do not damage 211 Series MXP Specific Product Precautions 3 Be sure to read before handling.