SMC Pneumatic Clean Series Appropriate tightening torque (Nm) Bolt Without auto switch With auto switch 6 8 10 10 1.06 M3 x 0.5 0.5 10 0.4 0.4 8 Allowable lateral load W (N) Allowable lateral load W (N) 0.3 0.3 8 Tightening torque Tightening torque 0.2 0.2 6 6 0.1 0.1 Allowable kinetic energy Caution 0 4 6 8 10 15 20 Stroke ST (mm) 0 4 6 8 10 15 20 Stroke ST (mm) When driving an inertial load, operate a cylinder with
20 191 11 20 50 98 70 44.5 16 84 11 6.4 117.5 316 3.3 280 46 20 196 20 11 50 70 98 44.5 84 13 11 6.4 117.5 319 3.3 Note 1) For AC20 only, the position of the pressure gauge is above the center of the piping.
10 5 2.86 20 10 5 Parameter *1,*2 Para.
The appearance is the same as the single solenoid. However, the construction allows the armature inside the solenoid to hold the A side ON position and B side ON position during momentary energization (20 ms or longer). The operating method and functions are the same as the conventional double solenoid type.
.5-18 5.8.4 Command:LOC Key-lock setting (R) .5-19 5.8.5 Command:LOC Key-lock setting (W).5-20 5.8.6 Command:STR Saves data (W) .5-21 5.9 Negative response.5-22 Chapter 6 Communication alarm function . 6-1 6.1 Communication alarm occurs .6-1 6.2 Communication alarm reset.6-2 6.3 Setting and checking.6-2 6.3.1 Setting and checking items.6-2 6.3.2 Setting and checking.6-3 HRSH Series HRX-OM-R028
The Grounding point should be as near as possible to the controller. Keep the grounding cable as short as possible.
w w t t t q q q e IN OUT IN OUT IN OUT y y y e e r r r u u u Drain Drain Drain Parts list Material No.
19 20 19 20 19 20 19 20 19 20 19 20 19 20 COM (Based on IEC529) Station 1 Double wiring Station 2 Single wiring Station 3 Double wiring Station 4 Single wiring (Refer to the connector wiring diagram.)
As a guide, refer to the proper tightening torques shown below.
ih* phfi &Jt vJ300-10-1A Tyw 42R (External pilot lype) Station I o2T, staf,o"s lT, 20 I 20 stations A port siae Ts llcarr.romfMs) B3T lo"d !
ih* phfi &Jt vJ300-10-1A Tyw 42R (External pilot lype) Station I o2T, staf,o"s lT, 20 I 20 stations A port siae Ts llcarr.romfMs) B3T lo"d !
1 AS-F AS-F !1 !2 TMH !2 !3 w ASD t y q i o e u t y q i o e u AS w AS-FE !0 KE !0 AS-FG !9 AS-FP Meter-in type Meter-out type Meter-out type Meter-in type AS-FM Seal method: Face seal For G thread AS-D AS-T r !8 !4 !6 !7 !5 !1 ASP ASN !2 AQ w t y q i o e ASV AK !0 VCHC ASR ASQ u @0 Meter-in type Meter-out type Component Parts No.
Number of fingers and therefore, mg F 2 x With "a" as the safety margin, F is determined as follows: mg F = x a 2 x When = 0.2 When = 0.1 mg F = x 4 2 x 0.2 mg F = x 4 2 x 0.1 = 10 x mg = 20 x mg 10 x workpiece weight 20 x workpiece weight (Note) Even in cases where the coefficient of friction is greater than = 0.2, for safety reasons, SMC recommends selecting a gripping force which
Number of fingers and therefore, mg F 2 x With "a" as the safety margin, F is determined as follows: mg F = x a 2 x When = 0.2 When = 0.1 mg F = x 4 2 x 0.2 mg F = x 4 2 x 0.1 = 10 x mg = 20 x mg 10 x workpiece weight 20 x workpiece weight (Note) Even in cases where the coefficient of friction is greater than = 0.2, for safety reasons, SMC recommends selecting a gripping force which
Size: 40, 60, 80, 100 A A A A-A r q e w A A-A e r q w Component Parts No.
VQD 24V 12V 100V 200V 110V 220V 24V DC 12V DC 100V AC 200V AC 110V AC 220V AC AXT100-20-2-05 AXT100-20-2-06 AXT100-20-2-01 AXT100-20-2-02 AXT100-20-2-03 AXT100-20-2-04 To remove manifold from DIN rail: 1) Loosen the clamp screw on the A side of both ends of the manifold. 2) Lift the A side of the manifold off the DIN rail and slide it in the direction of the B side.
It can also be used as a negative common.
Single Axis Electric Actuator Series LJ1S Series LJ1S Slider Guide Lead screw lead mm Mounting Page Model Series Guide type Motor type orientation Slide screw 20 20 20 20 20 20 LJ1S10 LJ1S20 LJ1S30 LJ1S10 LJ1S20 LJ1S30 88 Standard 90 motor 92 Slider guide LJ1S Horizontal 94 Standard 96 motor 98 Option specifications Page 100 Made to Order 101 Dust seal specification 116 TSUBAKI CABLEVEYOR
Examination of Load Rate an A 0.25 B 0.375 C 0.25 D 0.073 an 0.948 Decision an1 ML2B32 is selected 20 . With Guide 1. Operating Conditions Model : ML2B25 Load : 30N Speed , Va : 350mm/s Mounting Direction : upon wall W The weight of table is considered as 0 in this case. However, during actual application, it should be taken into consideration. 2.