Air cylinder Select and air filter with a filtration size of 5m or smaller. 2) Take measure to ensure air quality, such as by installing an after cooler, air dryer or water separator. Compressed air that contains a large amount of drainage can cause malfunction of pneumatic equipment such as valves.
(M4),90 , -9 M4 1.5Nm -10 14 - 6-3. 5080 O 6-3-1. 4 50 : 12.5Nm 63 : 24.5Nm 80 : 42.0Nm -11 6-3-2. 1) -12 -12 2) 15 - 6-3-3. GR-S-010(10g),GR-S-020(20g) 1) 2) 3)O 4) -13 -13 6-3-4. 1)() -14 2)() -14 16 - 6-4. 6-4-1. B , 1 6-4-2. 7. 7-1.
:12:0.15~1.0MPa 20:0.1~1.0MPa :0~60 4. , , , 2. ,, 5. 6. 1. , 5m 2. , 1. , 2. , 3. , ,, 1. , 2. , , 1. () 1. , 2. 145 CEP1, , 2. , 3. F.G.(), F.G. 3. 4. 4.
A filtration degree of 5m or less should be selected. 3. Install an aftercooler, air dryer or drain catch before the filter and take appropriate measures. Compressed air that contains excessive foreign material may cause malfunction of valves and other pneumatic equipment.
Nm JMHZ2-16D M3x0.5 0.59 14 - 3 Force Sensor LAN LAN HAN D (5x10) M5x10 3.0Nm 15 - M6x23 6.3Nm M4x10 1.0Nm 16 - P145-2. M3x7 0.59Nm 17 - 12 (No.1No.4)KQ2L04-M3G1 KQ2L04-M3G1 2(TCU0425B-1) 3(M44 ) TCU0425B-1 44 (No.1No.4)6 () 5(KQ2H04-06A1)1)4 6 () 4 6 KQ2H04-06A1 18 - () 19 - 5-3 1. 2. 3. 4. 1.() 2. 5m 3. 4. 5 5-4. 1.
Install the filter with auto drain (filtrarion 5m or less) to the system where the compressed air is cooled. For detailed information regarding the quality of the compressed air described above, refer to "SMC's Cleaning Systems". 2. Ambient environment Operate within the operating ambient temperature range(5~60). 3.
(In the case of external pilot specification) (15) (9) Higher voltage or wrong coil used Burnt coil (10) Coil splashed by water Air leaks through EXH. port [3(EB), 5(EA) port] of main valve.
Note 1) The tightening torque should be 0.5 Nm +/15%. Note 2) The applicable outside diameter of cable (7) is 6 to 8 mm. Note 3) Round or Y-shaped crimped terminal cannot be used. Reassembly Procedure 1)Insert cable gland (4), washer (5) and rubber seal (6) and housing (2) into cable (7) in order.
Select an air filter with a filtration size of 5m or smaller. of compressed air When components are removed, first confirm that measures are in place to prevent workpieces from dropping and/or equipment running away, etc. Cut the supply pressure and electric power and exhaust all compressed air from the system.
(In the case of external pilot specification) (15) Higher voltage or wrong coil used Burnt coil (9) Coil splashed by water (10) Air leaks through EXH. port [3(EB), 5(EA) port] of main valve.
Select and air filter with a filtration size of 5m or smaller. 2) Take measure to ensure air quality, such as by installing an after cooler, air dryer or water separator. Compressed air that contains a large amount of drainage can cause malfunction of pneumatic equipment such as valves.
Foreign matter entering the product. -15- Failure Major causes Countermeasures Operation at high speed Adjust the speed by the speed controller and keep the Damage to the parts. specified range.
With auto switch Basic/CS1BQ (mm) Bore (mm) 125 140 160 Stroke range (mm) S A H AL ZZ lB lC D E F G J K KA M MM N P 1/ 2 to 1000 98 50 110 47 235 145 115 36 90 43 16 M14 X 1.5 15 31 27 M30 X 1.5 35 1/ 2 to 1000 98 50 110 47 235 161 128 36 90 43 16 M14 X 1.5 15 31 27 M30 X 1.5 35 3/ 4 256.5 to 1200 106 56 120 53 182 144 40 90 43 18.5 M16 X 1.5 17 36 30.5 M36 X 1.5 39 CS1BQ125SCS1125, #1 CS1BQ140SCS1140
CH4 CH3 Pressure value for each channel are displayed at 2-second intervals. 15 16 Series PSE Safety Instructions These safety instructions are intended to prevent a hazardous situation and/or equipment damage. These instructions indicate the level of potential hazard by a label of "Caution", "Warning" or "Danger".
Tightening torque Thread Appropriate tightening torque Nm (kgfcm) M3 M5 0.3 to 0.5 (3 to 5) 1.5 to 2 (15 to 20) Wiring 1Polarity When DC power is to be connected to a solenoid valve equipped with light and/or surge voltage suppressor, check for polarity indications.
Magnet: D (Magnet), Shaft Type: S (Single Shaft), Size: 15, Thread Type: M5: 10, 15; Rc 1/8: 20, 30, 40, Rotation Angle: 90 (80° to 100°), Auto Switch: M9P--Solid State, Gen. Purpose, 3 Wire PNP, Horizontal, Lead Wire or Prewired Connector: Z (5m)
Magnet: D (Magnet), Shaft Type: S (Single Shaft), Size: 15, Thread Type: M5: 10, 15; Rc 1/8: 20, 30, 40, Rotation Angle: 90 (80° to 100°), Auto Switch: M9B--Solid State, Gen. Purpose, 2 Wire, Horizontal, Lead Wire or Prewired Connector: Z (5m)
Magnet: D (Built-in), Bore Size: 15 (5/8 Inch), Magnetic Holding Force: H (Large Holding Force), Stroke: 1500 (15 Inch), Adjuster: B (Shock Absorber (2 pcs.)), Auto Switch: A73HZ--Reed, DC Volt.>5,<24, AC Volt.<100, LED, Lead Wire, Horizontal, 5M
Magnet: D (Built-in), Bore Size: 15 (5/8 Inch), Magnetic Holding Force: H (Large Holding Force), Stroke: 1500 (15 Inch), Adjuster: Adjuster Bolt, Auto Switch: F7PVZ--Solid State, Gen. Purpose, 3 Wire PNP, Lead Wire, Vertical, 5M
Magnet: D (Built-in), Bore Size: 15 (5/8 Inch), Magnetic Holding Force: L (Small Holding Force), Stroke: 1500 (15 Inch), Adjuster: BC (Cap Type Shock Absorber (2 pcs.)), Auto Switch: F7PWZ--Solid State, 2-color Indication, 3 Wire PNP, Horizontal, 5M