KQ-OMS0022 No.KQ*-OMS0022-C Product Name Stainless Steel 316 One-touch Fittings Model / Series / Product Number Series KQG2 Contents 1. Safety Instructions 2 to 3 2. Specific Product Precautions 4 to 9 3. Specifications 10 to 11 4. Troubleshooting 11 5. Construction 12 6.
Do not exceed the screw-in torque of 7 to 9 Nm when installing piping. Exceeding this value may cause malfunctioning of the sensor. 4. Do not use pressure sensors with corrosive and/or flammable gases or liquids. 5. Allow a sufficient margin of tube length in piping in order to prevent application of torsional, tensile or moment load to the tubes and fittings. 6.
50.6 Vacuum supply port Vacuum pad connection port 20.5 RESET button DOWN button Pneumatic circuit SET button UP button Lead wire length 600 51.5 (3000) ZSE ISE ZSP 58 PS PV ISA 18 10.2 8 PSE 6.5 10.25 10 22.6 5.75 ZSE3-0X--D IS Vacuum supply port 2 x 3.3 Mounting hole Vacuum pad connection port 0X: M5 x 0.8 0XY: M6 x 1.0 ISG 0X: M5 x 0.8 0XY: M6 x 1.0 ZSM Connector type ZSE3-0X-C 7 50.6
8 F 24 VDC 5 G DIN terminal 24 VDC With surge voltage suppressor A B D E H J L M 4 H 100 VAC Size 2 2 1/4 N.C. 7 J 110 VAC Aluminum 4 5 N.O. 3/8 K 200 VAC 7 L 230 VAC 4 8 7 Resin (With bracket) M Conduit terminal 24 VDC With surge voltage suppressor 4 N 100 VAC 10 7 P 110 VAC A B C D E F G H J K L M N 5 Q 200 VAC Size 3 3 N.C. 8 1/4 R 230 VAC 10 (N.C. only) 6 N.O.
BMP1-032 70C J Nylon tarpaulin 110C K Heat resistant tarpaulin Maximum ambient temperature for the rod boot itself. 6-7-5
Suspension equipment and lifting devices also require measures to prevent dropping. 7) Consider the possibility of power source related malfunctions.
7 !8 @1 @6 14A !9 @0 CJ1 CJP @7 i o CJ2 80, 100 CM2 C85 !0 !1 CG1 @2@3@4@5 14B MB Locking at rod end C95 CA1 CS1 Manual release non-locking style: L Material Note Component Parts Material Note Component Parts No. q w e r t y No. !7 !8 !
(No freezing) Ambient temperature 0 to 60 C (No freezing) Maximum viscosity 5000 mPas Recommended operating cycle 1 to 7 Hz (0.2 to 1 Hz also possible depending on conditions)Note 2) Pilot air solenoid valve recommended Cv factor Note3) 0.45 Weight 3.0 kg Mounting orientation Horizontal (with mounting foot at bottom) Packaging General environment Note1) With cycles at 2 Hz or more.
Precoutions on Selection 7 7. Precautions on Design 7 8. Mounting Methods 8 9. Piping 11 10. Operating Environment 12 11. Speed Control 12 12. Clean Series / Precautions 13 13. Troubleshooting 17 14. Auto Switch 18 1 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.
To remove and install the snap ring for the knuckle pin or the trunnion pin, use an appropriate pair of pliers (tool for installing a type C snap ring for hole).
ZS-10-5 A-50 1 pc. 0.6 m 30 3 m 50 5 m Specifications Model ZSP1-B ZSP1-S Fluid Air Operating pressure range 20 to 101 kPa Applicable adsorption nozzle dia. 0.3 to 0.7 (Refer to Graph (1) on page 16-7-3.) 0.5 to 1.2 (Refer to Graph (2) on page 16-7-3.)
LT C edition Safety Instructions Be sure to read Precautions for Handling Pneumatic Devices (M-03-E3A) before using.
ON ON A (/) 1 OFF OFF DC(+)DC(-) 2 ON DC(+)DC(-) NPN PNP () 3 OFF ( ) () DC(+) DC(-) () 4 () 5 -47NO.ZK2-OM00801-B No. 80 mA (Er1,2) () ( (Er1,2) ) (Er0,4,6,7,8,9) DC24 DC24 V10% (Er0 4 6 7 8 V10% 9) 6 "HHH" (HHH) "LLL" (Er3) (LLL) (Er3) 3.5 F.S. DC24 V10% DC24 V10% DC(+) DC(-) 7 -48NO.ZK2-OM00801-B No.
Specifications .7 3-3. Gripping force .8 3-4. Dimensions .10 3-5. Connector and pin layout . 11 3-6. Center of gravity . 11 4.Product Specifications .13 4-1. Magnet gripper .13 4-2. 3-port solenoid valve .14 4-3. Auto switch .15 5.Operating method or operation .16 5-1Precautions for Design .16 5-2. Installation .17 5-3. U R C a p .20 5-4. Air supply .26 5-5. Piping .26 5-6.
Applicable actuator and operation range (angle) Sensor unit D-Y7K Air gripper (mm or ) Model Bore size (mm) 10 4 12 16 20 25 32 40 50 63 80 100 MHZ2 MHL2 MHS2 (2 finger) MHS3 (3 finger) MHS4 (4 finger) MHC2 MHW2 Parallel gripper 7 8 8.5 7 5 Wide opening 6.8 10.5 11 12.5 8.5 8 Parallel gripper 6.5 7 7.5 8.5 Parallel gripper 6.5 7 7.5 8 Parallel gripper 6.5 7 7.5 8.5 30 to 10 30 to
Rotate it clockwise until it stops. 7. Set the lock mechanism and check that the cover is locked completely.
10.2 8 10 17.8 11 5.5 2-3.3 Mounting hole Connector type: ZSP10X C Adjusting needle ADJ Pressure sensor Vacuum supply port 20 08 Adsorption nozzle port 7 48.3 Lead wire length 600 (3000) Adsorption nozzle port 0X: M5 x 0.8 0XY: M6 x 1 Vacuum supply port 0X: M5 x 0.8 0XY: M6 x 1 59.5 50 PV 6.5 10.2 8 5.5 17.8 11 10 2-3.3 Mounting hole 16-7-4
3 Hard anodized Nickel plated Tube Hexagon socket head cap screw C Carbon steel Aluminum alloy w !4 20Clear anodized Rod cover Magnet Magnetic material Aluminum alloy e !5 Chromated Piston Plug Carbon steel Aluminum alloy r !6 Data Electroless nickel plated Piston rod Element Resin Carbon steel t !7 Anodized Plate Snap ring Spring steel Aluminum alloy y !
When setting, allow 7 digits or more between P1 and P2 (and P3 and P4). Less than 7 digits will not allow correct operation. This operation manual is intended for those who have knowledge of machinery using pneumatic equipment, and have sufficient knowledge of assembly, operation and maintenace of such equipment.