Clamp Cylinder Series CK1 Do not leave out the component parts when the piping port location is changed. Even if one of the component parts is not replaced, malfunction may occur, resulting in dangerous operation. 2. To prevent air leakage, re-wind the pipe tape and fit into the changed location when the piping port location is changed.
Installation location Do not install this product in an area that is exposed to water or direct sunlight. Do not install in locations influenced by vibrations. If it must be used in such an area due to unavoidable circumstances, please contact SMC beforehand. 14-9-4 5 Booster Regulator Series VBA1110 to 4200 4.
For air
Do not allow repeated bending or stretching forces to be applied to lead wires. Wiring arrangements in which repeated bending stress or stretching force is applied to the lead wires can cause broken wires. 1. Do not drop or bump. Do not drop, bump or apply excessive impact (1,000m/s) when handling.
Do not hold the release button to avoid damage. VS DIN Rail Removal/Mounting To remove manifold from DIN rail: 1) Loosen the clamp screw on the "A" side of both ends of the manifold. 2) Lift the "A" side of the manifold off the DIN rail and slide it in the direction of the "B" side.
Do not drop or bump. Do not drop, bump or apply excessive impact (1,000 m/s2) when handling. Even if the switch body is not damaged, the switch may suffer internal damage that will lead to malfunction. 2. Hold the product from the body side when handling. The tensile strength of the power cord is 49 N, and pulling it with a greater force can cause failure. 3.
Vcior on up to 4 S des Ava able (lvlagnet Type) s NCQT very Cornpact sides and do Black Line s NCOB Outer Rcd C rcll] is B;mba Flat lrt Fla'.1r, s re!'
O ver range of i nput si gnal Pl ease execut e "i ni t i al i ze ( ref er t o P16) " w hen I TV do not operat e norm al l y af t er rest art i ng t he pow er suppl y. Readi ng or w ri t i ng errors occurred i n EEPRO M . Pl ease cont act us, w hen I TV do not operat e norm al l y af t er i ni t i al i ze.
Contact Protection Boxes/CD-P11, CD-P12 Auto Switch Internal Circuits Reed switches
Do not allow repeated bending or stretching forces to be applied to lead wires. Wiring arrangements in which repeated bending stress or stretching force is applied to the lead wires can cause broken wires. 1. Do not drop or bump. Do not drop, bump or apply excessive impact (1,000m/s) when handling.
Note) When using the D-M9A(V), do not use the steel set screws which are included with the auto switch mounting brackets above (BMB10-032, BMB5-032, BA7-040, BA7-063).
Gripping fingers do not scrape the tube during insertion or removal. 2. Body SMCs composite body offers: 1. Weight savings 2. Compact dimensions 3. High performance 4. Superior chemical resistance 2. Lower insertion and release forces. 7.
(Do not tighten with pliers.) RB J D How to change position of electrical entry After separating the terminal block from the terminal cover, change the position of the terminal cover to any desired direction (4 directions at every 90) to change the position of electrical entry.
Do not use a pair of pliers, nippers, or scissors because they could result in an uneven cut or cause the tube to become flattened. As a result, it might not be possible to connect the tubing, or after the tube has been connected, it could pull out or allow air to leak.
NVV5Z5-4 2-( 05 ) 1 -r87T) Y -r.Stationsa asize ot A, B port E-?
When mounting the product, please do not block the exhaust port at the center of the body as this may cause performance issues.
NVV5Z5-4 2-( 05 ) 1 -r87T) Y -r.Stationsa asize ot A, B port E-?
Matching the Ejector to the Vacuum Circuit Caution For precautions associated with matching the ejector to the vacuum circuit, refer to the technical data on page 13-1-10 to 13-1-19. 13-6-2 Vacuum Ejector In-line Type Series ZU How to Order ZX ZU 05 S ZR ZU07 ZM Maximum vacuum pressure S 85 kPa ZH L 48 kPa ZU05 ZU Nozzle diameter 05 0.5 mm ZL 07 0.7 mm Circuit diagram ZY EXE ZQ Specifications
W With locking at head side With locking at rod side q Do not use a 3 position solenoid valve. Avoid using circuit with 3 position solenoid valve (especially closed center). When pressure is trapped in the port with locking mechanism, end lock is free.
Do not plug or tighten it. (P port) (A port) (R port) 5-5-11 2 Series VGA342 Made to Order Specifications: Please contact SMC for detailed specifications, dimensions and delivery.