Process Pump Do not allow it to idle for a long time. If the pump is operated for a long time without any fluid inside or in a gas-fluid mixed state, the diaphragm may be damaged or the life may be shortened. Do not continue idling except for priming the pump. 5 11.
not occur on the product of the cooling method -W. 2: These alarms do not occur on the product of the power specification '-20'.
CAUTION Do not allow air flow that exceeds the rated flow. If the air flow is allowed outlet side the range of the rated flow even momentarily, drainage and lubricant may splash at the outlet side or cause damage to the component. Do not use in a low pressure application (such as a blower).
A magnet is built inside of guide block for use near a with the auto switch, so do not use near a magnetic disk, magnetic card, or magnetic tape. Data might be erased. 4. When mounting an air slide table, use screws with appropriate length and do not exceed the maximum tightening torque. Tightening with a torque above the limit could malfunction.
Do not use the product where these are present.
Do not use the product where these are present.
Do not use the product where these are present.
Do not use the product where these are present.
Refer to 4.3.2 Setting and checking,5.3.2 Setting and checking. 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Do not connect any wire to other PIN numbers.
CAUTION Do not allow air flow that exceeds the rated flow. If the air flow is allowed outlet side the range of the rated flow even momentarily, drainage and lubricant may splash at the outlet side or cause damage to the component. Do not use in a low pressure application (such as a blower).
Do not apply excessive lateral loads to the piston rod.
V100 SY SYJ Blanking plug KQP-23-X19 KQP-04-X19 KQP-06-X19 KQP-08-X19 KQP-10-X19 Dimensions VK L (mm) A Applicable fittings fitting d Model A L D VZ Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com KQP-23-X19 KQP-04-X19 KQP-06-X19 KQP-08-X19 KQP-10-X19 16 16 18 20.5
The latching solenoid option(with self holding mechanism)functions in the same manner as a 2 position double solenoid but uses only one solenoid to do the job.
NPTF Bottom 04 sP0105 %,,NPTF SidE 5 AXT 333-21 Terminal Block Subolate ME4OI SLR Lell and Right end plates-Shorl w/o conduil NPT threads. Includes (3)O-rings AFP 568-015 1 pr.
Do not use in locations having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. In locations near heat sources, block off radiated heat. 1. Operate within the range of the maximum operating pressure. Caution 1. After a long period of non-use, perform inspections before beginning operation. 2.
Symbol -X80, -X81 Main Value Double Acting Type 1 A N 06 5 1 4 VP31 1 D Z X81 Body size CE marking Nil Q None CE-compliant 4 6 8 1/2 1 1 1/2 3/8 1/2 3/4 1 1 1/4 1 1/2 2 Port size (IN, OUT port) Thread type Symbol VP3145 VP3165 VP3185 Port size Nil F N T D/DO/DZ/DU only Rc G NPT NPTF 03 04 06 10 12 14 20 Type of actuation X80 X81 Double solenoid Single solenoid External pilot Passage, Type
Applicable model 84 84 03 FGD-CV002-04 06 03 FGD-CV003-04 06 03 FGD-CV004-04 06 03 FGD-CV001-04 06 32 32 FGDT/F FGDT/F FGDC/E FGDC/E Note 1) Same as standard product except for cover assembly Note 2) 03, 04, and 06 indicate the relevant port sizes (Rc3/8, 1/2, 3/4).
Also, take measures to prevent ingress of water and foreign matter from the breathing port of the diaphragm. 5-5-10 1 3 Port Air Operated Valve Series VGA342 How to Order SA 04 VGA342 A VA Port size Passage A Normally closed (N.C.) B Normally open (N.O.) Thread type Nil Rc F G N NPT T NPTF 04 1/2 06 3/4 10 1 SA VA JIS Symbol VM N.C. N.O.
Do NOT make upward piping. 2. Float type auto drain (N.C.) 1) Compressor can be used even if energy is under 3.7 kW. 2) Set operating pressure more than 0.15 MPa. 2. Float type auto drain (N.C.) DO NOT pipe upwards. 446 SP093-001I Issued: Sep 2009 P.G.
Conditions for mechanical operation Do not move the mechanical operation beyond the operating limit position, as this could damage the mechanical valve itself and lead to equipment malfunction. Actuator stroke Operate the mechanism within the stroke range that has been obtained through the formula given below. (Do not move beyond the operating limit position.)