ARM10/11 OUT fitting type AMR Inch size Metric size Straight Elbow Straight Elbow Symbol Symbol 4 5/32 6 1/4 ITV 4 6 5/32 1/4 04 05 16 17 54 55 66 67 Note 1) A pressure gauge with a full span of 0.4 MPa is attached. Note 2) The oil-free type has nongreased fluid contact areas. IC VBA A ARM11B 1 A R 1 06 Z Individual supply type VE 1 2 3 4 5 6 1.
A Me1 Me1 = 1 /3WeL1 = 1/3150.2 = 0.1 [Nm] 4 = Me1/Me1 max = 1/10 = 0.1 W We L1 Review Me1. n = 1 + 2 + 3 + 4 = 0.111 + 0.125 + 0.091 + 0.10 = 0.427 Can be used based on n = 0.427 1 48 Series REAH Model Selection 4 Max.
Description Qty Applicable model Anti-quake bracket A Anti-quake bracket B 2 2 4 4 HRR-TK001 HRR050-A/W-20/40-UY Nut (M8) Bolt (M8) Mounting of anti-quake bracket 1. Remove the cap from M8 stud bolt. (4pcs) 2. Mount the anti-quake bracket A. (Recommended torque : 12.5Nm) 3. Mount the anti-quake bracket B.
0 1 Standard Micro load Port size Nil 02 N02 With gasket Rc 1/4 NPT 1/4 16-9-3 2 Series IS3000 Construction Precautions IS3000-02/3010-02 (Rc 1/4 thread) Be sure to read before handling.
ANSI symbol shows the valve as a single inlel 4.way, bul valve may be used, withoul modilica. tion, as a dual inlet 4.way, a 3.way, or a 2-way, by piping and/or plugging lhe appropriate ports.
x Width 925 x Depth 955] HRS150-W -20-A 459 [208] HRS150-A-20
231 Height 1710 x Width 1185 x Depth 955 HRS150-Al-l-A 237 HRS100-Wl-l-A 205 Height 1610 x Width 925 x Depth 955 HRS150-Wl-l-A 208 IDH Forklift insertion side HRS150-A-20
-10AS G46-2-02 G36-2-01 G46-2-02 G46-2-02 G46-2-02 0.2MPa Note 3) GC3-2AS GC3-2AS GC3-2AS GC3-2AS GC3-2AS Note 1) Assembly includes a bracket and set nuts.
Input block type (Fill out for I/O unit only) Ports 2, 4 size (metric) Nil Without input block M12: 2 inputs M12: 4 inputs M8: 4 inputs (3-pin) Ports 2, 4 Symbol C8 C10 C12 02 03 B CM 1 2 3 Ports 1, 3, 5 8 One-touch fitting 10 One-touch fitting 12 One-touch fitting 1/4 3/8 Bottom ported Rc 1/4 Mixed Input block (Fill out for I/O unit only) 1: 1/2 3, 5: 3/4 Nil Without SI unit/input block
Choose a filtration degree of 5m or finer. A mist separator (AM) is suitable. 3. Compressed air which includes a large amount of drainage can cause malfunction of valves and other pneumatic equipment. As a countermeasure, install and air dryer or after cooler, etc. 4.
40 A 4 cores x 8 mm2 (4 cores x AWG8) (Including grounding cable) R8-5 HRSH250--20 50 A 4 cores x 8 mm2 (4 cores x AWG8) (Including grounding cable) R8-5 M5 A HRSH100--40 20 A 3 x 5.5 mm2 (3 x AWG10) (Power supply) 1 x 14 mm2 (1 x AWG6) (Grounding cable) R5.5-5 (Power supply) R14-5 (Grounding cable) HRSH150--40 HRSH200--40 HRSH250--40 3-phase 380 to 415 VAC (50/60 Hz) 30 A Note) An example
Diaphragm B moves to the right, and at the same time diaphragm A also moves to the right pushing pilot valve A. 3. When pilot valve A is pushed, air acts upon the switching valve, drive chamber A is switched to a supply state, and the air which was in drive chamber B is exhausted to the outside. 4.
Diaphragm B moves to the right, and at the same time diaphragm A also moves to the right pushing pilot valve A. 3. When pilot valve A is pushed, air acts upon the switching valve, drive chamber A is switched to a supply state, and the air which was in drive chamber B is exhausted to the outside. 4. When air enters drive chamber A, diaphragm B moves to the left pressing pilot valve B. 5.
Note 2) Window comparator mode Since hysteresis is 3 digits, separate P1 and P2 by 7 digits or more. 1 digit is the minimum setting unit (refer to the table above). 4 Digital Flow Switch for Air Series PFA How to Order How to Order Display Unit Sensor Unit PFA 30 PFA5 10 02 0 A 0 Mounting Flow rate range Panel mount DIN rail, wall mount A B 1 to 10l/min 5 to 50l/min 10 50 Wiring specifications
Hs Auto switch 24.5 A B 49.5 A 33 B Proper auto switch mounting positions (mm) D-G39 D-K39 D-A3 D-A44 D-H7 D-H7C D-H7W D-H7BAL D-C7 D-C80 D-C73C D-C80C D-B5 D-B64 D-G5NTL D-H7F D-B59W Bore size (mm) A B A A A A A A B B B B B B 16 15.5 7.5 12 14 17.5 12.5 11 19 20 8 4 6 9.5 4.5 25 17.5 13.5 17 7 15.5 19 10.5 14 20.5 7.5 3.5 5.5 9 4 32 20.5 16.5 9 20 18.5 22 23.5 12.5 17 9.5 5.5 7.5 11 6 40
Take sufficient shielding measures when operating the product in any of the following places. ( 1 ) A place where noise due to static electricity etc. is generated ( 2 ) A place of high electric field strength ( 3 ) A place where exposure to radioactivity is possible ( 4 ) A place near power cable Do not operate the product in a place where there is a source of surge.
After tightening by hand, tighten an additional 1/4 rotation for M3 and 1/6 rotation for M5 with a tool. However, when using a miniature fitting, tighten an additional 1/4 rotation with a tool after tightening by hand. Also, when there are 2 gaskets such as in case of a universal elbow or universal tee, tighten an additional 1/2 rotation.
Rated voltage 3 2 1 110 VAC 50/60 Hz 200 VAC 50/60 Hz 100 VAC 50/60 Hz Model Port size (Rc 1/4) (Rc 3/8) (Rc 1/2) (Rc 3/4) (Rc 1) 02 03 04 06 10 2232 2232 2242 2352 2362 4 5 6 7 8 9 220 VAC 50/60 Hz 24 VDC 12 VDC 240 VAC 50/60 Hz 48 VAC 50/60 Hz Other (Please contact SMC for inquiry.) Refer to the table (1) given below for availability. Refer to page 17-3-65 for ordering a coil only.
VHS400-02 VHS401-02 VHS400-03 VHS401-03 VHS400-04 VHS401-04 VHS500-06 VHS501-06 Pipipng direction Port size 3 4 1 2 3 8 1 4 1(P) 2(A) 21 105 76 54 35 35 57 93 Effective area (mm2) Mass (kg) 2(A) 3(R) 0.25 0.34 The front face of the handle is the reference position. Easy to Operate The direction of air flow can be verified at a glance by the orientation of the handle.