<br>However, the D-M9□ series auto switch will be shipped together with the product but not mounted to the cylinder.<br>In addition, commercially available set screws cannot be used to mount a BM8 type auto switch mounting band because their shapes differ.<br>The set screw for the BM8 is designed to prevent deformation of the cylinder tube.

<br>For the 2-finger type: the MHZAJ2-6, MHZJ2, MHK2 series, and the MHZL2-X6110. <br>For the 3-finger type: the MHSJ3 series (which can be found in the MHS3 series web catalog). <br>The material of the dust cover can be selected, and depending on the series, special order specifications such as dust cover adhesion and caulking are also available.

<br>Check this when connecting the communication unit. When “Normal” or “Easy” is started, the controller setting software automatically checks the connected controller. <br>However, communication cannot be performed if the communication setting of the COM port number is different.

<br>③ Check if the same method is selected for both the positioning unit (pulse oscillator) and the pulse signal. For the LEC-W2 controller setting kit, check the parameter value of “Options set 1” at the bottom of the parameter window with the setting software (ACT controller).

<br><br>How to check return to origin completion: The completion of the return to origin operation is confirmed by a SETON signal. <br>However, the SETON signal is turned ON when the first return to origin operation is completed, and the signal remains ON thereafter.

<br>If a reference point sensor is required for use in conjunction with an LECS series motor driver, mount a separate sensor. <br>When using return to origin in conjunction with an LECP series controller or an LECPA series motor driver, as a pushing operation is used to return to origin, an origin sensor is not required.

<br>Note that neither is included with the controller. The part number of the teaching pendant is “LEC-T1-3JG(S).” <br>The controller setting software was formerly a CD-ROM (sold separately), but it can now be downloaded from the SMC website. <br>The controller setting software can be found here.

<br>For other signals, refer to the controller operation manual.

<br>If you want to change the corresponding actuators, you must reset these specific parameters. <br>The setting of these parameters must be performed at one of our factories in order to prevent problems from occurring. <br>Contact your local SMC sales representative to put in a request for repair.

<br><br>Example: Positioning operation, operation method ABS, step no. 1 = 50 mm, step no. 2 = 0 mm <br>The actuator moves forward by instructing step no. 1 to operate, and if step no. 2 is instructed to operate before completion, it will retract and stop at the position of 0 mm.

<br>It operates according to the position and speed data from the master PLC instead of using step data that has been edited (rewritten) beforehand using a PC or teaching box.<br><br>

<br>If there is no terminating resistor, there will be interference during communication.<br>An SMC terminating resistor (LEC-CGR) can be ordered, or a terminating resistor can be prepared separately by the customer.<br>Note) “LEC-CGR” is an optional part number of SMC’s gateway unit (LEC-G).

<br>The “Component Parts” table can be found in the “Motor Mounting Parts” section of the LEFS series motorless type electric actuator catalog.<br>Note 1) The same applies to the LEY-AP□ and LEJ-AP□ of the LEY and LEJ series motorless type.

<br>By simply supplying compressed air, large flow rate vacuum and blowing greater than the supply volume is possible. <br>The ZH□-□-X185 vacuum flow features a discharge flow 4 times the supply air volume and suction flow 3 times the supply air volume. <br>The ZH□-□-X185 catalog can be found here.

<br>① When there is no piping rotation stopper, the part numbers are as follows: IRV10-01/02□-X3 and IRV20-02/03/04□-X3. <br>② When there is a piping rotation stopper, the part numbers are as follows: IRV10-01/02□-X28 and IRV20-02/03/04□-X28. <br>The IRV10 series catalog can be found here.

Replace the element after 1 year of use or when one of the following occurs: <br>① When the pressure drop reaches 20 kPa at negative pressure:<br>ΔP(20 kPa) ② When the time until the vacuum pressure is reached is longer than the set time of the device: <br>set time (T) ③ When there are no remarkable changes in the operating environment conditions (vacuum ÷ release frequency, dust amount,

<br>Also, please use the product selection function of our "Energy saving program." <br>Please contact your SMC sales representative if you have any questions.<br>Refrigerated Air Dryer Model Selection Software

<br>To only remove water droplets, use an AMG series water separator. <br>To remove water vapor (dehumidify), use an ID□ series air dryer. <br>“Dry air” refers to air that has been dehumidified by an air dryer. Note that water separators cannot remove water vapor, so if the temperature drops in subsequent pipes, water droplets will be generated.

<br>Without auto drain: Drain can be discharged by loosening the drain cock at the bottom of the body housing (case) by turning it counterclockwise. (After discharge, do not forget to return the drain cock to its original position by tightening it clockwise.) <br>With auto drain: Normally, drain discharge is performed automatically when drain accumulates, so no action is required.

<br>Note 1) For option “H” (auto drain, 1.6 MPa specification), the auto drain cannot be replaced. <br>Note 2) Option “J” (drain guide specification) does not have a built-in auto drain. <br>The new air preparation filter catalog can be found here.