AS-FPQ/AS-FPG T M5 type H (width across flats) Applicable tubing O.D. d A A4 D1 L3 D2 M1 L1 T L2 Model Weight (g) Note 2) Tubing O.D. d T H D1 D2 L1 L2 L3 M1 L4 Max.
The port A pressure is fed back to the control circuit by the pressure sensor.
5 15-17-5 6 Series AS-FPQ/FPG Dimensions H (width across flats) Applicable tubing O.D. d A L4 D1 L3 D2 M1 L1 L2 T M5 type H (width across flats) Applicable tubing O.D. d A A4 D1 L3 D2 M1 L1 T L2 Model Weight (g) Note 2) Tubing O.D. d T H D1 D2 L1 L2 L3 M1 L4 Max. Min. Max. 1 2 Min.
When you begin to feel that the screw is being tightened, turn it further by 90. MHKl2-12 0.4 0.4 1.6 MHKl2-16 0.4 0.4 1.6 MHKl2-20 0.4 0.4 1.6 MHKl2-25 0.4 0.4 1.6 Protrusion of Auto Switch from Edge of Body The protrusion of an auto switch from the edge of the body in the table below. Use the table as a guideline for mounting.
(Normally Open) merely by turning over the switch cover.
Measurement instruments that SMC manufactures or sells have not been qualified by type approval tests relevant to the metrology (measurement) laws of each country.
During an emergency when the air supply is cut off, it is used to alleviate a problem by forcibly pushing the release piston back to release the lock. However, take note that the sliding resistance of the piston rod will be high compared to unlocking with air pressure. 2.
In case of heavy soiling, wipe it off with a cloth soaked in a neutral detergent diluted with water after wringing it out thoroughly, and finish up by wiping with a dry cloth.
In addition, when atmospheric pressure is desired, shut off the power after reducing the set pressure, and then introduce atmospheric pressure by using a vacuum release valve, etc. i If the power for this product is cut off by a power failure, etc. when it is in a controlled state, the setting side pressure will be held temporarily.
Note 3) Intermediate stroke is available by the 1 mm interval.
The air pressure that flows in acts on diaphragm C and while opposing the force generated by diaphragm B it also acts on diaphragm A opposing the compression force of the setting spring and becomes the set pressure.
Products approved by CSA or UL standards are accepted in most states and governments beyond question.
It then acts on diaphragm B as nozzle back pressure, the main valve is pushed down by the generated force, and the supply pressure flows out to the downstream side. The air pressure that flows in acts on diaphragm C. While opposing the force generated by diaphragm B it also acts on diaphragm A, opposing the compression force of the setting spring and becomes the set pressure.
MHK2-12S 120 12 9 4 9 13 76 Normally open Normally closed MHK2-16S 16 23 6 14.6 20.6 114 DL1 MHK2-20S 20 34 10 16 26 237 L2 MHK2-25S 25 58 14 19 33 443 20MHK2-12C 12 12 4 9 13 76 MHK2-16C 16 25 6 14.6 20.6 115 MHK2-20C 20 44 10 16 26 237 MHK2-25C 25 73 14 19 33 443 Series MHKL2/Long Stroke Type Note) Width at opening (mm) L2 Width at closing (mm) L1 Effective gripping force per finger (N)
MHK2-12S 120 12 9 4 9 13 76 Normally open Normally closed MHK2-16S 16 23 6 14.6 20.6 114 DL1 MHK2-20S 20 34 10 16 26 237 L2 MHK2-25S 25 58 14 19 33 443 20MHK2-12C 12 12 4 9 13 76 MHK2-16C 16 25 6 14.6 20.6 115 MHK2-20C 20 44 10 16 26 237 MHK2-25C 25 73 14 19 33 443 Series MHKL2/Long Stroke Type Note) Width at opening (mm) L2 Width at closing (mm) L1 Effective gripping force per finger (N)
Secure each wire by retightening the terminal screw. d Tighten the ground nut to secure the cable wire. Locking slotted style Push the manual override button with a small screw driver until it stops. Turn it in the counter-clockwise direction at 90o, and it is locked.
For standard installation, turn 15 to 30 using tool, after fastening by hand. Pay attention not to over torque the product.
) Valve model C [dm3/ (sbar)] b Cv C [dm3/ (sbar)] b Cv Grommet 0.12 0.10 0.10 0.10 0.12 0.37 0.33 0.34 0.38 0.12 0.43 0.40 0.40 0.35 0.54 0.12 0.19 0.09 0.11 0.14 0.37 0.10 0.30 0.11 0.10 M5 x 0.8 0.45 0.84 0.38 0.48 0.63 VK3120 Used as a 3 Port Valve 1 8 Body ported 90 VK3120Y (For low wattage 2 W DC) M5 x 0.8 0 to 0.7 Series VK3000 can be used as 3 port valve, as a N.C. or N.O. type, by
Change of electrical entry (Orientation) After separating terminal block and housing, the cable entry direction can be changed by attaching the housing in the desired direction (4 directions in 90 increments). In the case of w/indicator light, avoid damaging the light with lead wire. Precautions Plug a connector in or out vertically, never at an angle.
Pressure Range: 0 to 1 MPa, Piping: Rc 1/4, Output Specification: I/O Link: Switch Output 1 + Switch Output 2 [Switch Output: NPN or PNP Switching Type], Unit Specification: Unit Selection Function, Switches w/Unit Selection not Permitted for Use in Japan, Lead Wire: Lead Wire with M12 Connector; Straight, 5 m, Bracket: -, Operation Manual/Calibration Certificate: -