Series CM2-Z 10-/11- ø20, ø25, ø32, ø40 21-/22- Air Cylinder Use caution when handling a cylinder, which is running at a high speed and a high frequency, because the surface of a cylinder tube could get so hot enough as to cause you get burned. 4. Do not use an air cylinder as an air-hydro cylinder. If it uses turbine oil in place of fluids for cylinder, it may result in oil leakage. 5. The oil stuck to the cylinder is grease. 6.
(mm) D-A90V D-A96V D-A93V 22 Bore size D-M9V D-F9WV D-M9 D-F9W D-A90 D-A96 D-A93 (mm) 32 20 32 Mounting pattern q, w 35 Mounting pattern e 20 12 Mounting of Auto Switch As shown below, there are 3 ways to mount the auto switch according to 3 types of electrical entries. Insert the auto switch into the switch groove.
(mm) D-A90V D-A96V D-A93V 22 Bore size D-M9V D-F9WV D-M9 D-F9W D-A90 D-A96 D-A93 (mm) 32 20 32 Mounting pattern q, w 35 Mounting pattern e 20 12 Mounting of Auto Switch As shown below, there are 3 ways to mount the auto switch according to 3 types of electrical entries. Insert the auto switch into the switch groove.
The programmed Key(s) will give an output signal for as long as the key is depressed.
Besides, the whole accuracy after mounting on an equipment may be varied depending on the mounting condition and surroundings. As an equipment, calibration should be done by customer.
Besides, the whole accuracy after mounting on an equipment may be varied depending on the mounting condition and surroundings. As an equipment, calibration should be done by customer.
These switches are not rated as explosion proof. Never use in the presence of an explosive gas as this may cause a serious explosion. Pressure Setting Caution 2. Do not use in an environment where a strong magnetic field is present. 1. The switching setting indication scale shows the set value for pressure decrease.
2 r AS t q w AS-FE r y KE t u AS-FG i i o AS-FP !0 u AS-FM y !3 w !1 AS-D Meter-in type Meter-out type e Meter-in type Meter-out type AS-T ASP ASN Component Parts Component Parts AQ No.
Front matter 7 16 Flow Characteristics Note) Use this graph as a guide. In the case of obtaining an accurate flow rate, refer to front matter pages 1 to 6.
Speed Adjustment Throttle speed controller, such as Series AS, is recommended for speed adjustment.
Speed Adjustment Throttle speed controller, such as Series AS, is recommended for speed adjustment.
Trouble shooting 9.1 Alarm and Warning POINT Turn the servo-ON (SON) OFF and shut off the main circuit power supply as soon as the alarm occurs. An alarm or warning is displayed when an abnormality occurs during operation. When an alarm or warning occurs, take appropriate measures according to "LECSN-T Operation Manual, Chapter 8. When an alarm occurs, the ALM is turned off.
It can be used alone as a tank.
D3 Input block stations AS-i, 8 in/8 out, 31 slave modes, 2 power supply systems Nil 1 None 1 station For 20 stations D20 AS-i, 4 in/4 out, 31 slave modes, 2 power supply systems AS-i, 8 in/8 out, 31 slave modes, 1 power supply system Note) In case of D0, only DIN rail fittings are attached.
Never use in an atmosphere of explosive gases. The switches do not have an explosion proof rating. Never use in the pressure of an explosive gas as this may cause a serious explosion. Maintenance Warning Mounting 1. Perform a periodical inspections for proper operation of the switch. Unexpected malfunctions may cause possible danger. 2.
Actuator drive When an actuator, such as a cylinder, is to be driven Provide ventilation when using a valve in a confined area, such as in a closed control panel.
8 Carbon steel 12, 20 Rod end nut Brass !
When an air cushion is required on both ends, it is available as a made-to-order -X1515. Caution X1515 CK1 Enter the standard model no.
optional manifotd mounted deslgn is available tor the NVS 3115 valves, The block 13 aluminum bar Etock with common supply and exhaust as wellaa an individual outlet port on the side.