Flow sensor Part number Description Remarks ZS-36-A1 1 station: 2 L-type brackets With mounting screws (M3 x 15 L) 2 pcs. ZS-36-A2 2 station: 2 L-type brackets With mounting screws (M3 x 25 L) 2 pcs. ZS-36-A3 3 station: 2 L-type brackets With mounting screws (M3 x 35 L) 2 pcs. ZS-36-A4 4 station: 2 L-type brackets With mounting screws (M3 x 45 L) 2 pcs.
Controller model Mounting screw Mounting bracket assembly LC1-1H-N3 M3 x 0.5 LC1-1-N3 Power terminal: TB LC1-1H-N5 M5 x 0.8 LC1-1-N5 LC1-1H-L3 M3 LC1-1-L3 LC1-1H-L5 M5 LC1-1-L5 Communication connector: CN3 Motor power line connector: CN5 Mounting with T-nuts Regenerative absorption unit connector: CN6 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main
or less at 24 VDC Indicator LED Red LED illuminates when turned ON.
or less at 24 VDC Indicator LED Red LED illuminates when turned ON.
less at 10 mA (2 V or less at 40 mA) Leakage current 100 A or less at 24 VDC Indicator light Red LED illuminates when turned ON.
Applied voltage When connecting fittings to valves, tighten as indicated below. 1) M3, M5 types 1. When using SMC fitting, follow the guidelines below. After tightening by hand, tighten an additional 1/4 (M3), 1/6 (M5) turn with a tightening tool. However, if miniature fittings are used, tighten an additional 1/4 turn with a tightening tool after tightening by hand.
Rated voltage VFN M5 x 0.8 1 2 3 100 VAC, 50/60 Hz 200 VAC, 50/60 Hz 110 VAC, 50/60 Hz 220 VAC, 50/60 Hz Light/Surge voltage suppressor 4 Nil None Z 5 6 24 VDC 12 VDC S With light/surge voltage suppressor 9 With surge voltage suppressor Other Option Not available for GZ, HZ and DOZ Electrical entry Grommet L plug connector M plug connector DIN terminal G: Lead wire length 300 mm L:
15 to 30 VDC Power supply 24 VDC10%/5% For valve Internal current consumption (Unit) 70 mA or less 50 mA or less Output type NPN output (+COM.)
PB08 PG2 12 No.PA083 37 rad/s 1 1000 PB09 VG2 12 PA083 823 rad/s 20 50 PB10 VIC 12 PA083 33.7 ms 0.1 1000.0 PB11 VDC No.PB243No.PB240 980 0 1000 PB12 OVA C4MR Configurator2 0 0 TM % No.PA0145No.PB120 5% 100 PB13 NH1 1 1 No.PB01()1 4500 Hz 100 4500 No.PB010 5 15 5 No.
ZS-32-A Length: 2 m (With rubber cover) Note Lead wire with connector Mist separator regulator AWM20/AWM30/AWM40 For ISE35--A (AR/AW series) Mounting thread (M3 x 7L, 2 pcs.), adapter, lock pin, O-ring are attached ZS-32-C Mounting option Micro mist separator regulator AWD20/AWD30/AWD40 For ISE35--B (ARM10/11 series) Mounting thread (M3 x 13, 2 pcs.), adapter, lock pin, O-ring are attached
Table 4 BoltTightening torque Size Bolt Recommended tightening torque 10 M3 0.63 Nm 15 20 M4 1.50 Nm 30 M5 3.00 Nm 40 Fig.8 Mounting 2 Using a plate with tapped holes (Refer to Fig. 9). L dimension when the unit is used as a flange is shown in the table below.
OFF M3 hexagon screw Tightening torque 0.6 Nm 1 2 0 0 0 IP address 192.168. Y . X : Thread size: M3 x 30 The following instructions must be followed during maintenance: Turn off the power supply. Stop the air supply, exhaust the residual pressure and verify that the air is released before performing maintenance. Otherwise an injury can result.
Valve manifold Accessories Side D NOTE (SI unit side) Replacement of the SI unit Remove the M3 hexagon screws from the SI unit and release the SI unit from the valve manifold. Replace the SI unit.
This product is not designed to be explosion proof. 4 4 4 6 6 6 ON Connected load: 24 VDC Solenoid valve with surge voltage suppressor of 1.5 W or less (manufactured by SMC) Current consumption of power supply for SI unit operation: 0.1 A max.
Check that the M3 hexagon socket head cap screws have been tightened to the specified torque. If these items are not adhered to, it may lead to damage to the unit or intrusion of liquid or dust into the units.
with Va) M2=Wx L1=15x0.05=0.725Nm M2 0.75 Load factor a2= = =0.375 M2max 2 Dynamic load
Put a hexagon socket head cap screw (M3 x 0.5 x 14 L) through the auto switch's through-hole (2 locations), and then push it down into the M3 tapped part on the auto switch mounting bracket while turning it lightly. 3.
M3 hexagon screw Tightening torque 0.6 Nm Terminating resistor Valve manifold : Thread size: M3 x 30 Troubleshooting The following instructions must be followed during maintenance: Turn off the power supply. Stop the air supply, exhaust the residual pressure and verify that the air is released before performing maintenance. Otherwise an injury can result.
radius 80 3.4 13 4.5 6 Series ITV0 Dimensions Single unit for manifolds 56 50 PWR ERR M8 x 1 Cable connection threads 15 15 9 84 86 3.7 Breathing hole Note) (M3 x 0.5) OUT OUT port (4, 5/32") 8 2 5 18.5 Note) When used under the conditions equivalent to IP65, use the regulator after piping a fitting/tube into a breathing hole.
Put a hexagon socket head cap screw (M3 x 0.5 x 14 L) through the auto switch's through-hole (2 locations), and then push it down into the M3 tapped part on the auto switch mounting bracket while turning it lightly. 3.