SMC Corporation of America
Elite Part Number Search
Search Results "HRSH250-W-20-AS"

l Y w H w Y w l l " i I I I r r l i | v l l . s o w d ; l w | v w f f Y L : f <.t __ I i i Y f Fw -t wl5uwl sor-;sS sownsot Y r.L. rr 5 r r a r s o s o w l s o w f s o v l , * ; * 1 i ' l , l -1 l a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a MX9IEtr-@EHN+NE_I T l I r I I I I l I o , o o @ o a @ @ @ esrio" ruup @Auto switch See

The controller is sold as single unit after the compatible actuator is set. q Check the actuator label for model number.This matches the controller. w Check Parallel I/O configuration matches (NPN or PNP). q w Refer to the operation manual for using the products.

The maximum number of stations is 20 in terms of manifold bases, as well as solenoids. (Please consult with SMC for more stations.)

Keep wiring as short as possible to prevent interference from electromagnetic noise and surge voltage. Do not use a cable longer than 20 m. Wire the DC(-) line(blue) as close as possible to the power supply. Environment Do not use the product in area that is exposed to corrosive gases, chemicals, sea water, water or steam. Otherwise failure or malfunction can result.

9 Cushion seal A Steel ball A Urethane Carbon steel %6 @0 Steel ball B Same as cushion seal A Carbon steel @1 Cushion seal B Urethane %7 except 20, 25 standard stroke Tooth ring Stainless steel @2 Cushion ring gasket A Bumper NBR Urethane %8 @3 C type retaining ring for taper ring Carbon steel @4 Same as cushion ring gasket A except 20, 25 standard stroke Cushion ring gasket B NBR %9 C type

Refer to page 6-12-20 regarding stopping accuracy. 3. In order to further improve stopping accuracy, the time from the stop signal to the operation of the lock should be shortened as much as possible.

SS5Y5 10 NA 05 N M S U C 8 6 Refer to page 20 for Type 11/ Bottom ported dimensions. Mixed Mounting Type q w e r t o y !0 u i It is possible to mount SY3000 size valves on all stations. In this case, there is no need to fill in part i in the order code.

R E SY3/5/7000 SS5Y 20 T H R E A D T Y P E PT 00T NPTF M A N I F O L D S E R I E S V A LV E S TAT I O N S 3 SY3000 5 SY5000 7 SY7000 02 2 Stations to 20 20 Stations H O W T O O R D E R B O D Y P O R T E D W/ I N D I V I D U A L L E A D W I R E SY3/5/7000 SY 20 B R A C K E T S E R I E S Without Bracket F1 With Foot Bracket F2 With Side Bracket 3 SY3000 5 SY5000 7 SY7000 A, B P O R T S I Z

load W(N) 5 40 4 30 30 30 3 25 25 20 2 20 20 16 10 16 1 10 10 100 75 60 30 100 75 60 30 Stroke (mm) Stroke (mm) Note 1) The indicated allowable lateral load at the rod end is for the rod end female thread.

2 i r i t y w w e !0 !0 !2 !5 o !0 !4 q q y u !1 !3 r t !1 M5 type U10/32 type M5 type U10/32 type !1 y !2 u !4 !3 i !5 u e r r t w e o !0 i o q q t y !0 !2 w !

60PG (20 pins) 60PH (10 pins) Note 1) Types 60PG and 60PH differ only in their connectors, and the L1 through L4 dimensions are the same as type 60P.

3 Lube with double end lock CBA1-63A-PS-W CBA1-50A-PS-W CBA1-40A-PS-W CBA1-80A-PS-W CBA1-100A-PS-W Lock bushing 1 Zinc bronze die cast !4 MG Non-lube with double end lock Lock spring 1 Steel wire Zinc chromated !5 CBA1N63A-PS-W CBA1N50A-PS-W CBA1N40A-PS-W CBA1N80A-PS-W CBA1N100A-PS-W Bumper 1 Urethane !6 MGP @8, @9, #0, #1, #3, #4 are packed together as one set of packings.

3 MGC Lube with double end lock CBA1-63A-PS-W CBA1-50A-PS-W CBA1-40A-PS-W CBA1-80A-PS-W CBA1-100A-PS-W 1 Lock bushing Zinc bronze die cast !4 Non-lube with double end lock 1 Lock spring Steel wire Zinc chromated !5 CBA1N63A-PS-W CBA1N50A-PS-W CBA1N40A-PS-W CBA1N80A-PS-W CBA1N100A-PS-W MGF 1 Bumper Urethane !6 @8, @9, #0, #1, #3, #4 are packed together as one set of packings.

The maximum number of stations is 20 in terms of manifold bases, as well as solenoids. (Please consult with SMC for more stations.)

4 @1 w @3 !0 !2 @2 r o e @4 !0 y !3 12, 16 under 50 stroke 12, 16 over 30 stroke !5 20, 25 over 30 stroke under 100 stroke 12, 16 over 50 stroke @0 Under 50 stroke 20, 25 over 50 stroke Under 30 stroke 20, 25 over 100 stroke MGPM32 to 100 MGPL32 to 100 i !8 !7 u q y !1 !9 @3 !0 !2 @2 r o e !4 @4 @1 !0 w !

The Grounding point should be as near as possible to the controller. Keep the grounding cable as short as possible.

Holder mounting bracket q -X416 Holder mounting bracket w -X417 Fine stroke adjustment range (Treated as a special order when exceeding the adjustment ranges shown below.)