HRX-OM-X037 For a facility with a large installation area that can vent the air naturally: Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2. For a facility with a small installation area that cannot vent the air naturally: Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.
Brown 2 A B-1 Red 1 A A-1 Cable length (L) Orange 6 B B-2 Yellow 5 B A-2 8m *1 8 Green 3 COM-A/COM B-3 10m *1 A Blue 4 COM-B/ A-3 Shield 15m *1 B Cable color Terminal no. Vcc B-4 Brown 12 *1) produced upon receipt of order. 20m *1 C GND A-4 Black 13 A B-5 Red 7 A A-5 Black 6 B B-6 Orange 9 Only Robotic type cable can be B A-6 Black 8 3 selected.
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
For a facility having a large installation area (that can vent the air naturally): Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2. For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level.
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
C DA 30 30 30 H A A H H A H W1 T C Symbol: A16 Symbol: A17 Symbol: A18 Symbol: A19 MM AL DA MM 30 30 30 30 MM MM H A H A H A C H A 36 MWB Series Symbol: A20 Symbol: A21 Symbol: A22 Symbol: A23 RD 30 30 MM 30 DA MM 30 DA MM L DB DB C H A T H A T H A B W H A L K Symbol: A24 Symbol: A25 Symbol: A26 Symbol: A27 DA MM DA MM MM MM 30 30 H AL A H L A H AL H AL L K LB K Symbol: A28 Symbol: A29
No Servomotor Rotation Direction can Pn000 0 0001 (+Counter motors side ) Tuning-less Function Related Switch Pn170 1401 1401 Electronic Gear Ratio (Numerator) *1 Pn20E 4 65536 Electronic Gear Ratio (Denominator) *3 Pn210 1 1250 750 375 1500 1000 500 1875 1250 625 LEFS25(L,R) LEFS32(L,R) LEFS40(L,R) Series Lead symbol H A B H A B H A B Lead 20 12 6 24 16 8 30 20 10 Parameter *1,*2 Para.
Refer to the Auto Switches Precautions for using with an auto switch. 14.When a cylinder is used in a clamping, suspending, or lifting mechanism There is a danger of workpieces dropping if there is a decrease of thrust due to a drop in circuit pressure caused by a power outage, etc.
Be certain to adopt a reliable connecting method if the rotary actuator is used very frequently or if it is used in a location that is exposed to a large amount of vibration. Consider the possibility of a reduction in the circuit air pressure caused by a power failure.
Take note that the leakage voltage will increase when a resistor is used in parallel with a switching element or when a C-R circuit (surge voltage suppressor) is used for protecting a switching device because of the leakage voltage passing through the C-R circuit. The suppressor residual leakage voltage should be as follows. 8.
Do not install piping to the product with a misalignment. A permanent load will be applied to the product after piping. When a flexible hose is used for the piping, the hose must be fixed with a bracket etc.
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
HS D-A7H D-A80H D-F7 D-J79 D-F7W D-J79W D-F7F D-F7NT D-F7BAL 40, 50 25, 32 Approx. 30.5 A A Approx. 22 A A Approx. HS 40, 50 25, 32 D-A73C D-A80C D-J79C Approx. 30.5 Approx. 26.6 A A A A D-A79W D-F7WV D-F7V D-F7BAVL 25, 32 40, 50 Approx. 30.5 Approx. 22 A A A A 40, 50 D-P5DW Approx. 31 A A Approx.
Initial value Recommended value No Servomotor Rotation Direction can Pn000 0 0001 (+Counter motors side ) Tuning-less Function Related Switch Pn170 1401 1401 Electronic Gear Ratio (Numerator) *3 Pn20E 4 65536 Electronic Gear Ratio (Denominator) *3 Pn210 1 1250 750 375 1500 1000 500 1875 1250 625 LEFS25(L,R) LEFS32(L,R) LEFS40(L,R) Series Lead symbol H A B H A B H A B Lead 20 12 6 24 16 8
The set values for OUT1 are displayed in auto-preset mode as follows: Normal output Reversed output P_1 = A (A B)/4 n_1 = B + (A B)/4 A = Max. pressure H_1 = (A B)/2 H_1 = (A B)/2 B = Min. pressure The display of set values of OUT2 is changed at the number after "_", i.e. "P_2", "n_2" and "H_2".
Do not use the lock as a safety lock or a control that requires a locking force. The lock used for the product with a lock is designed to prevent dropping of work piece. 2. For vertical mounting, use the product with a lock. If the product is not equipped with a lock, the product will move and drop the work piece when the power is removed. 3.
Taper ring Steel ball P f R R High locking efficiency Greater locking efficiency as well as stable locking and unlocking operation has been achieved by arranging a large number of steel ball bearings in circular rows.
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.