VCW

Note 3) When using seal material PTFE at 15 cm3/min (under water pressure) or less. Note 4) Vibration resistance Conditions when tested with one sweep of 10 to 250 Hz in the axial direction and at a right angle to the armature, in both energized and deenergized states. No malfunction occurred when tested (value at the initial state).

For Dry Air, Pilot Operated Series VQ20/30 2 Port Solenoid Valve

Turn it in the counter-clockwise direction at 90o, and it is locked. Turn it right to release. 3.8 Change of electrical entry Wire entry can be changed by mounting the housing in either direction (four directions at every 90) after dividing the terminal block and the housing. For the indicator lighted style, be careful not to damage the light with the lead wire of the cable.

NCRBIBwserbs

Corxtruction./ Parts List 27A' PartsList Note: The rotation specilication of270', the point of minimum rotation 20' is a limit shifring point even il the switch is shifted to make rotation of switch as shown in the left diagram. (E\ren if switch is shitted tothe maximum, switchon will be made at the point prior to the stopping ooint at 20'.)

ZL3-OM00601

If a sealant tape is used, leave 1 thread exposed at the end of threads.

Rotary Actuator NCRB1BW Series Single Vane / Double Shaft

Corxtruction./ Parts List 27A' PartsList Note: The rotation specilication of270', the point of minimum rotation 20' is a limit shifring point even il the switch is shifted to make rotation of switch as shown in the left diagram. (E\ren if switch is shitted tothe maximum, switchon will be made at the point prior to the stopping ooint at 20'.)

Wireless System

one end) 1 place Current (Wired) SI unit: 15 units 1 line (Connector at one end) 14 lines (Connector at both ends) 29 places Interchangeability maintained * Maximum I/O of wireless master/ slave unit is limited to 128 points.

Air cylinder

Too large resistance of In particular, attention should be paid to the piping equipment used and fittings because they are often missed. on the way of Equipment and piping at the exhaust side should piping also be of an appropriate size. Operation at a very low speed can create a The product 1.

SI Unit for Vacuum Manifold

Fixed at 0x29.

VP3145/3165/3185

Test was performed at both energized and deenergized states in the axial direction and at the right angles to the main valve and armature.

ITVH

mA DC, 0 to 20 mA DC (Sink type) Voltage type 0 to 5 VDC, 0 to 10 VDC Input signal Preset input type 4 points (Negative common) Current type 500 or less Voltage type 6.0 to 6.5 k (at 25C) Input impedance Preset input type Approx. 4.7 k 1 to 5 VDC Output impedance: 1 k or more Output accuracy: 6% F.S. or less Analog output Symbol 4 to 20 mA (Sink type) Output impedance: 250 or less Output

Series VQ4000 Base Mounted Plug-in/Plug Lead Single Unit For details about certified products conforming to international standards, visit us at www.smcworld.com.

the bottom. 50 mA at 24 VAC, DC or less 20 mA at 100 VAC, DC Max. operating current Note 1) Rated voltage: 24 VDC to 100 VAC Internal voltage drop: 4 V Note 2) Combination of VQ41 (Single) and release valve spacer can be used as air release valve.

Cylinder with lock

Note 2) D-M9 and A9 type cannot be mounted on square groove of the CP96N series. 19 - Auto switch proper mounting position (Detection at stroke end) 20 - 3-4. Wiring method and examples of auto switches 21 - 4. Maintenance 4-1. Consumable parts Fig. 9 Replaceable seals 4-1-1. Seal kit Bore size (mm) Order No.

Digital Pressure Switch

Analogue output Output impedance approx. 1 k Output current (rated pressure range) 4 to 20 mA 2.5%F.S. 2.4 to 20 mA Current output 3 2.5%F.S. Linearity 1%F.S.

Large Size 3 Port Solenoid Valve VP3145/3165/3185 Series Rubber Seal

Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature.

IDX-OM-Y002

Auto drain Check the auto drain is working properly at least once a day.

AS-FG/ASD-FG

AS121FG-M5 AS231FG-01 R(PT) 1/8 20, 25, 32 AS221FG-01 AS231FG-02 R(PT) 1/4 20, 25, 32, 40 AS221FG-02 AS331FG-02 R(PT) 1/4 40, 50, 63 AS321FG-02 AS331FG-03 R(PT) 3/8 40, 50, 63 AS321FG-03 AS431FG-04 R(PT) 1/2 63, 80, 100 AS421FG-04 AS131FG-U10/32 10-32UNF 6, 10, 16, 20 AS121FG-U10/32 AS231FG-N01 NPT1/8 20, 25, 32 AS221FG-N01 Elbow type AS231FG-N02 NPT1/4 20, 25, 32, 40 AS221FG-N02 AS331FG-N02

Handheld Electrostatic Meter

In this product, it is calculated to +20 (-20) = 40 kV because the rated charge is -20 kV to +20kV. (Ref.: 1%F.S.=400.01=0.4 kV) F.S. (Full Span or Full Scale) M The distance from the measured target to the head of the sensor. Refer to Procedure on page 10. The rated measuring distance is 50 mm. The display shows the charge amount range for a 50 mm measuring distance.

1 High Purity Chemical Valve Compact Type Series LVD VC
Space saving, compact type is available. Space saving, compact type is available. VDW Compact type is introduced as a new series to complement VQ Body: New PFA Body: New PFA Body: New PFA conventio

0 Insert pin assembly replacement screw Cut the end of the tubing y at a right angle and pass it through the fitting nut u.

Air Cylinder Short Type Standard: Double Acting, Single Rod CG3 Series ø 20, ø 25, ø 32, ø 40, ø 50, ø 63, ø 80, ø 100

A bending moment will be applied to the cylinder due to the vibration generated at the stroke end, and the cylinder may be damaged. In such a case, mount a bracket to reduce the vibration of the cylinder or use the cylinder at a piston speed low enough to prevent the cylinder from vibrating at the stroke end.

Information

Compatible PC When using setup software (MR ConfiguratorTM), use an IBM PC/AT compatible PC that meets the following operating conditions.