LG1H a = 2000 L1 (mm) Pitching Mep m : Transfer load (kg) a : Work piece acceleration (mm/s) Me: Dynamic moment L : Overhang to work piece center of gravity (mm) a = 3000 2000 m L1 0 10 20 30 Transfer load m (kg) L2 600 400 L2 (mm) Mer Rolling Yawing m 200 L2 Mer 10 20 30 0 Transfer load m (kg) m a = 1000 4000 a = 2000 L3 (mm) a = 3000 L3 2000 m Mey a 10 20 30 0 Transfer load m (kg) Refer to
For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.
At that time, make clearance of around 0.5mm between a stopper guide and a rotary unit. (2) Tighten a hexagon socket head cap screw .
Description Material AV2000-A AV3000-A AV4000-A AV5000-A 4 Pilot valve assembly*1) See below.
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
Series CJ2 is auto switch capable Standard double acting single rod, Bore sizes: 6, 10, 16 *, Strokes from 15mm through 200mm depending upon bore size, Mounts: basic, foot, front flange, double clevis, Variety of switches and a variety of lead wire lengths CJ2 ROUND BODY CYLINDER. CYLINDER. ACTUATOR. 10MM CJ2 DBL-ACT AUTO-SW. 0.3858 lb. EE.
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
(Equivalent lead (8)Cable length * [m] (7)Cable type (9)Driver type Power supply Without cable Nil Without cable Nil Compatible drivers voltage [V] Standard cable 3 3 S R Nil Without driver Robotic cable (Flexible cable) 5 5 200 to 230 200 to 230 M2 LECYM2-V A 10 U2 LECYU2-V C 20 * The length of the motor and encoder cables are the same.
OYTOT MSA 1010.02 Yes '/f t2) Yes MBA 10't r.02 11 Yes 't"et t ' l Z YE MAA 4210.02 t6 Y5 v." 11) v.' t2\ t " t2:l t ' l a STATX)flS 2 3 a 5 6 7 I t t0 -1 nm) 5 .
OYTOT MSA 1010.02 Yes '/f t2) Yes MBA 10't r.02 11 Yes 't"et t ' l Z YE MAA 4210.02 t6 Y5 v." 11) v.' t2\ t " t2:l t ' l a STATX)flS 2 3 a 5 6 7 I t t0 -1 nm) 5 .
(iii) Shift the result of (ii) one bit toward the least significant bit, and fill a zero into the most significant bit position. (iv) If the least significant bit was a 1, exclusive OR the result of (iii) with "A001h". If the least significant bit was a 0, no exclusive OR takes place. (v) Repeat (iii) to (v) until eight shifts have been performed.
solenoid ( ): 100 V, 110 VAC [ ]: 200 V, 220 VAC Note) Black (Blue) [Red]: A side solenoid () Red: A side solenoid (+) Black: COM () Red (Blue) [Red]: COM (+) Black (Yellow) [Yellow]: A side solenoid () Red: A side solenoid (+) Black: COM () Red (Blue) [Red]: COM (+) Plug connector lead wire length Note) The length of the lead wire provided is 300 mm.
Converting this to the adsorption state of the workpiece, the vacuum pressure reaches its maximum when the pad and the piping on the vacuum port (V) have no leakage. Vacuum pressure decreases when there is a lot of leakage when adsorbing a workpiece.
Description B VNH1 VNH2 VNH3 VNH4 VNH1-16 VNH2-16 VNH3-16 VNH4-16 Bracket (with bolt and washer) 4.2-30 VNH Specifications 3 port valve 2 port valve A B A B VNH311 20A A B VNH411 25A A B VNH113 10A A B VNH213 15A A B VNH313 20A A B VNH413 25A A B VNH133 10A A B VNH233 15A A B VNH333 20A A B VNH433 25A A B VNH111 10A VNH211 15A Model Operating fluid pressure Fluid Operation 0 to 7.0MPa 0 to
IDX-OM-W022-A PRODUCT NAME Refrigerated Air Dryer MODEL / Series IDU8E-10(-C,K,L,M,R,S,T) IDU8E-20(-C,K,L,M,R,T) IDU11E-10(-C,K,L,M,R,S,T) IDU11E-20(-C,K,L,M,R,T) IDU15E1-10(-C,K,L,M,R,S,T) IDU15E1-20(-C,K,L,M,R,T) IDU8E-23(-C,K,L,R,T,V) IDU11E-23(-C,K,L,R,T,V) IDU15E1-23(-C,K,L,R,T,V) Please read this manual prior of using the air dryer. Keep the manual readily available for reference.
Confirm that the surface temperature of the filter or the parts for operation (V-band, element, etc.) are 40C or less, to prevent a burn from occurring. Warning Operation 1. Never loosen the V-band under pressurized conditions. 59
VC 24 VDC 12 VDC 100 VAC 200 VAC 110 VAC SY100-82-3-05 SY100-82-3-06 SY100-82-2-01 SY100-82-2-02 SY100-82-2-03 24 V 12 V 100 V 200 V 110 V A VDW A VQ B DIN Terminal Circuit with Indicator Light VX2 A AC circuit DC circuit Mounting procedure 1) Hook the mounting hook on the side of the manifold base to the DIN rail. 2) Lift the side of the manifold off the DIN rail and slide it in the
V V S With V y Pilot port size * Port size: 14 only Select Nil for 06 and 10.
w w e q q ZP3-T-A-B ZP3-T-A-(02/04) w t r q Component Parts No.