Round Type Hydraulic Cylinder (The tightening torque should be about 2 to 3 Nm.) 5. Modification of the detecting position should be made in the condition of 3. 329
The cylinder ports are designed so that a maximum speed 3000 mm/s can be obtained. However, it may not be possible to attain the desired speed in the case of short cylinder strokes. It may also be impossible to attain the desired speed due to restriction by component equipment (valves, speed control valves, piping, fitting, etc.).
_c e. lf less th.n 5%, a siia er oode shou d be spec fed 2 Fof moonhng accessories sec p.ges 914 3. r8l indi.ares bdtDn mode, atsho.k rDsDlber 8L:t.rs.rnroi be added to ion butto. mo.le s of reroved 1om button node s OEr,f.1M to OEN1:10rv1 4. Lrethane sll ker caps are avalable as accessores frr rooets 0El"l1 15Mxr ro oEN,r1.25lv1r2 All diJiensions in lnches.
Select the cylinder with bumper (O N") it cushion valVe is to be fuH yopened. Tie rods or piston assembly may be damaged if neither air cushion nor bumper is utilized.
No code ISC ISO 00 08 Material 2) Indication of closed status. 3) Indication of opened status.
The cylinder ports are designed so that a maximum speed 3000 mm/s can be obtained. However, it may not be possible to attain the desired speed in the case of short cylinder strokes. It may also be impossible to attain the desired speed due to restriction by component equipment (valves, speed control valves, piping, fitting, etc.).
/EXH.) size Note) Silencer can only be selected for EXH. port with One-touch tting. The silencer part number depends on the size of the EXH. port. One-touch fittings Metric size Inch size 06 6 07 1/4" 08 8 09 5/16" 10 10 11 3/8" 12 12 13 1/2" ZH -X267 No silencer available for ZH18/20DA in inch size for EXH. port size '13'.
DXT170-71-1 OFF ON VQZ It can be locked in the ON state by turning the manual override to the right, setting the E mark to 1 and pushing it. It can be unlocked by turning the manual override to the left, setting the E mark to 0 and pushing it, and the manual returns.
In the case of SRF series, when the inlet pressure is released with the condition that the pressure at outlet side is maintained, the residual pressure cannot be released. If it will be necessary to eliminate pressure from the outlet side, a circuit should be provided for residual pressure relief. 1. Open the sealed package inside a clean room.
Because pipe fittings are press-fit, they must be replaced together with the cover assembly. r Those with a bore of 50 or more cannot be disassembled.
Actuation Warning 1 Normally closed q Cannot be used for vacuum retention. w Use a release valve. (Without a release valve, the workpiece may not be released.)
I nspect i on and m ai nt enance of m achi nery / equi pm ent shoul d onl y be perf orm ed once m easures t o prevent f al l i ng or runaw ay of t he dri ver obj ect s have been conf i rm ed. B. W hen equi pm ent i s t o be rem oved, conf i rm t he saf et y process as m ent i oned above.
Actuation Warning 1 Normally closed qCannot be used for vacuum retention. wUse a release valve. (Without a release valve, the work piece may not be released.)
With 8 One-touch fittings Note) Can be changed to side ported configuration.
Therefore, SMC products cannot be used for business or certification ordained by the metrology (measurement) laws of each country. Safety Instructions Be sure to read the Handling Precautions for SMC Products (M-E03-3) and Operation Manual before use.
S kit can be used by connecting to gateway unit.
P EB EA In common Type 23 Stacking type Individual wiring SY9 20 + + + + P. 43 EA P EB Manifold stations can be increased. Type 23P Stacking type Flat ribbon cable SY9 20 P. 53 Manifold stations can be increased.
required. 1000 27 60 105 155 190 257 330 1400 24 53 92 142 174 244 308 385 1800 23 48 82 127 160 230 296 366 It must be noted, however, that oversized piston rods transmit more side load 2400 19 45 75 114 145 213 281 347 than is the case with more flexible smaller rods; therefore, the use of oversized 3200 16 41 67 103 130 194 261 329 4000 13 38 63 94 119 175 240 310 rods should not be considered
All other options are available, whereas they may be stocked in lesser quantities or manufactured to order. Special arrangements can be made for repeating (blanket) orders of these product models. Contact your sales representative for further details. Several VQ models have been certified by the Canadian Standards Association and bear the CSA and NRTL/C trademark.
required. 1000 27 60 105 155 190 257 330 1400 24 53 92 142 174 244 308 385 1800 23 48 82 127 160 230 296 366 It must be noted, however, that oversized piston rods transmit more side load 2400 19 45 75 114 145 213 281 347 than is the case with more flexible smaller rods; therefore, the use of oversized 3200 16 41 67 103 130 194 261 329 4000 13 38 63 94 119 175 240 310 rods should not be considered