Magnet Gripper Unit for Collaborative Robots Hold/Release success: default output DO[101] Hold/Release failure: default output DO[102] * Digital output port can be selected within DO[101] to DO[112] * you select the same digital output port for different status signals, a warning message will be displayed. 2. Test run The manual operation of the magnet gripper unit can be checked.
Do not use in these conditions. (Refer to specifications.) Consult SMC if a fluid other than compressed air is used. 2.
not occur on the product of the cooling method -W. 2: These alarms do not occur on the product of the power specification '-20'.
Do not use pressure sensors with corrosive and/or flammable gases or liquids. 4. Connection of sensor connector Cut the sensor cable as illustrated to the right. Referring to the table below, insert each lead wire of the cable at the position marked with a number corresponding to 1.
Failure to do so may cause equipment failure or malfunction. 9. Mount the Fieldbus system in a location where there is no excessive vibration or shock. Failure to do so may cause equipment failure or malfunction. 10. Do not use in places where there are cyclic temperature changes.
Do not drop or bump. Do not drop, bump or apply excessive impacts (300m/s or more for reed switches and 1000m/s or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Do not mount the product in locations where it is exposed to radiant heat. 5. Do not use in dusty locations or where water, oil, etc., splash on the equipment. 6.
Do not use in locations where static electric charges will be a problem. Consult SMC regarding use in this kind of environment. 6. Do not use in locations where spatter occurs. There is a danger of spatter causing a fire.
Do not use in locations where static electric charges will be a problem. Consult SMC regarding use in this kind of environment. 6. Do not use in locations where spatter occurs. There is a danger of spatter causing a fire.
For type W, DC voltage is only 5 16" One-touch fitting for N9 5 5 16" One-touch fitting for N9 One-touch fitting for One-touch fitting for One-touch fitting for available.
through until it comes out the other side. 4) Do not get across steps with casters.
I" = 2. 4. 6. 8.. ) (n = 4.8, 12. 16") (n = 4, 8, 12. 16 .. ) (n = 4, 8, '2, 16 ..) With 2 pes. (DiUerent surfaCfls 115 20 120 ' 25 Same surface), With 1 pc (n '" 2. 4. 6, 8.. ~_-L_("":.:=,, 4 "2 ' :0 .. ,1 _ (" ,,.-,,8,-.' ' :0.. ) ".-,,. ' "2,,.-,-"." ) ,,.-,,8,-.' ,,.,,6.")
Do not operate with anything other than compressed air. The cleaning equipment has been designed to be used only with compressed air. To use fluids instead of compressed air, please contact SMC beforehand. 2. Do not use compressed air that contains chemicals, organic solvents, salt, or corrosive gases.
6Element mounting bracket 16-1 16-2 16-3 472 Series FGB Replacement Procedure of Element 2 4. Method for Removal of Element Assembly 2. Overhaul 2-1. If the differential pressure rises due to clogging and reaches the threshold for element replacement (0.1 MPa), replace the element with the new one. 2-2.
6Element mounting bracket 16-1 16-2 16-3 472 Series FGB Replacement Procedure of Element 2 4. Method for Removal of Element Assembly 2. Overhaul 2-1. If the differential pressure rises due to clogging and reaches the threshold for element replacement (0.1 MPa), replace the element with the new one. 2-2.
Pressure Do not use the product in the vacuum state which is substantially different from the atmospheric pressure (above sea level) and in the atmosphere under being pressurized. 2. Using inside a clean room Do not use the product in a clean room, as it could contaminate the clean room. Caution 1.
Do not drop or bump. Do not drop, bump or apply excessive impacts (1000m/s or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Do not mount the product in locations where it is exposed to radiant heat. 5. Do not use in dusty locations or where water, oil, etc., splash on the equipment. 6.
Do not mount the product in locations where it is exposed to radiant heat. 5. Do not use in dusty locations or where water, oil, etc., splash on the equipment. 6.
Communication example Slave Address : No.1 Read 16 pieces data from register 0030h.