Electric Rotary Table Compatible Compatible Compatible ORIG direction Set in units of 1/s Speed during return to origin position Set in units of 1 mm/s ORIG speed No setting required Set in units of 1/s2 Acceleration during return to origin position Set in units of 1 mm/s ORIG ACC Continuous operation at the set speed can be tested while the switch is being pressed.
Address Description of bytes tion unit range Input Mode D0410 4 Target position [m] Note 1) 1 Note 1) No D0412 2 Positioning time [0.01s] 1 0 to 6000 No D0413 2 Speed [mm/s] 1 0 to 400 No D0414 2 Acceleration [mm/s2] 1 0 to 60 No D0415 2 Deceleration [mm/s2] 1 0 to 60 No 1 to 20, Pushing speed [mm/s] D0416 2 1 No 32768 to Note2) 32788 Thrust setting value Note 3) More than D0417 2 1 Yes [
External terminals (including the FE terminal) and enclosure screws Insulation resistance 10 M or more 500 VDC External terminals (including the FE terminal) and enclosure screws EN61131-2 compliant 5f<8.4 Hz 3.5 mm Vibration resistance 8.4f<150 Hz 9.8 m/s2 Impact resistance EN61131-2 compliant, 147 m/s2, 11 ms Mounting Through hole for M4 screw (2 pcs.)
Maximum acceleration: 2000mm/s2 Positioning distance (mm) 1 1000 500 100 10 10 0.5 100.5 50.5 10.5 1.5 100 0.5 10.5 5.5 1.5 0.6 Speed (mm/s) 500 0.5 2.7 1.7 0.9 0.6 1000 0.5 1.9 1.4 0.9 0.6 A B C D Values will vary slightly depending on the operating conditions.
When selecting the overhang, refer to "Calculation of Guide Load Factor" or the Electric Actuator Selection Software for confirmation, http://www.smcworld.com Dynamic Allowable Moment Acceleration/Deceleration 1000 mm/s2 3000 mm/s2 5000 mm/s2 Orientation Load overhanging direction m : Work load [kg] Me: Dynamic allowable moment [Nm] L : Overhang to the work load center of gravity [mm] Model
.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com Acceleration Stroke Cushion seal RHC MK(2) 15 m/s2 5 m/s2 (REB) (REA) RS Q G High precision guide type: REAHT (Double axis) High precision guide type: REBHT (Double axis) RS H A REB REA RZQ High precision guide type: REAH (Single axis) High precision
(Unit: mm/s2) to 10 Deceleration 5000 5000 Sets the deceleration to reach the moving speed. (Unit: mm/s2) to 10 Selects the pushing operation or the positioning operation from the set value. For the pushing operation, this value specifies the force to be generated as a percentage of the maximum pushing force. (Unit: %) The maximum pushing force depends on the electric actuator.
ZB-OM00201-B Specifications General Specifications Ambient -5 to 50oC (No condensation) temperature range Fluid Air, inert gas Vibration 30m/s2 (Without pressures sensor/vacuum pressure switch, With pressure sensor) resistance Note 1) 20m/s2 (With switch) Impact 150m/s2 (Without pressures sensor/vacuum pressure switch, With pressure sensor) resistance Note 2) 100m/s2 (With switch) Note 1)
(STO switch) S2: Start switch (STO release switch) S3: On switch S4: Off switch KM1: Magnetic contactor K3: Safety relay EMG: Emergency stop switch CN3 EM1 or EM2 M Servo motor Note.
Do not drop, bump, or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Mount switches in locations where there is no vibration greater than 98 m/s2, or no impact greater than 490 m/s2. 3. Do not use in an area where surges are generated.
Do not drop, bump, or apply excessive impact (PSE540: 980 m/s2, PSE560: 500 m/s2) while handling. Although the body of the sensor may not be damaged, the inside of the sensor could be damaged and lead to malfunction. 2. The tensile strength of the cord is 50 N. Applying a greater pulling force to it can cause malfunction.
specifications Coil specifications Seal material NBR, FKM, EPDM, PTFE Ambient temperature (C) 20 to 60 1 to 60 (No freezing) Fluid temperature (C) VC Dusttight/low jetproof (equivalent to IP65) Enclosure VDW Environment Location without corrosive or explosive gases (3) Valve leakage (cm3/min) 0 (With water pressure) VQ Mounting orientation Unrestricted (4) Vibration/Impact resistance (m/s2
T1 T2 T3 T4 L 0.5 V (T1 + T3) V T2 = L : Stroke [mm] (Operating condition) V : Speed [mm/s] (Operating condition) a1: Acceleration [mm/s2] (Operating condition) a2: Deceleration [mm/s2] (Operating condition) 500 0.5 300 (0.1 + 0.1) 300 T1 = V/a1 [s] T3 = V/a2 [s] = P T2: Constant speed time can be found from the following equation. = 1.57 [s] T4 = 0.3 [s] T2 = [s] L 0.5 V (T1
(Error number 5) 4 points preset input type Brown Blue S1 White Vs Black S2 Vs: Power supply 24 VDC (Negative common) One of the preset pressures P1 through P4 is selected by the ON/OFF combination of S1 and S2. S1 OFF ON OFF ON S2 OFF OFF ON ON Preset pressure P01 P02 P03 P04 For safety reasons, it is recommended that one of the preset pressures be set to 0 MPa.
Impact acceleration [m/s2] 5 0 50 100 150 200 250 300 Speed [mm/s] Relationship between speed and impact acceleration 120 in vacuum environments (1.3 x 104 Pa) low leakage, and low outgassing.
itch (STO sw itch) S2: Start sw itch (STO release sw itch) S3: On sw itch S4: Off sw itch KM1: Magnetic contactor K3: Safety relay EMG: Emergency stop sw itch CN3 EM1 or EM2 M Servo motor Note.
(STO switch) S2: Start switch (STO release switch) S3: On switch S4: Off switch KM1: Magnetic contactor K3: Safety relay EMG: Emergency stop switch CN3 EM1 or EM2 M Servo motor Note.
Temperature abnormality On 16 Series E-MY2 Auto Switch Specifications Auto Switch Common Specifications Reed switch Solid state switch Type Leakage current 3-wire: 100 A or less 2-wire: 0.8 mA or less None Operating time 1.2 ms 1 ms or less 300 m/s2 1000 m/s2 Impact resistance 50 M or more at 500 VDC Mega (between lead wire and case) Insulation resistance Withstand voltage 1000 VAC for 1
Mount the switch in a location where there is no vibration greater than 98 m/s2, or no impact greater than 490 m/s2. 3. Do not use in an area where surges are generated.