Refrigerated Air Dryer -P.4 Rc1/2 IDF Rc3/4 IDU3E IDU4E IDU6E High inlet air temperature Saturation: 55C 0.7MPa 0.37 0.57 0.82 Rc3/8 Rc1/2 Rc3/4 0.32 0.52 0.75 2.2 3.7 5.5 HFC134a P.5-P.7 IDU 2 Series IDF/IDU E Selection Method IDF selection example IDU selection example Reading correction factor 1 Correction factor Note) Correction factor Data symbol Data symbol Note) Condition Condition Obtain the correction
input No., State (P-No.) label C-AND OR input time out subroutine call command General-purpose input No., State (P-No.) label C-OR AND input condition jump command General-purpose input No., State (P-No.) label J-AND Condition jump OR input condition jump command General-purpose input No., State (P-No.) label J-OR Program Control Commands Parameter value Mnemonic Classification Function
Table 1 Table 2 Output type ON YES Hysteresis mode For air OFF P-1 P-2 Display Instantaneous flow rate l/min Cumulative flow rate l Large flow rate "P" H H H (fixed hysteresis) = 3 digits CFM x 10-2 ft3 x 10-1 ON CFM = ft3/min Window comparator mode NO OFF P-1 P-2 For water Large flow rate OUT1 Output mode Display Instantaneous flow rate l/min Cumulative flow rate l ON YES OUT2 is the
center 3 position exhaust center 3 position closed center 3 position pressure center (1) 3 position exhaust center 3 position closed center (A) 4 (B) 2 (A) 4 (B) 2 (A) 4 (B) 2 (A) 4 (B) 2 (A) 4 (B) 2 (A) 4 (B) 2 5 (R1) 1 (P) 3 (R2) 5 (R1) 1 (P) 3 (R2) 5 (R1) 1 (P) 3 (R2) 5 (R1) 1 (P) 3 (R2) 5 (R1) 1 (P) 3 (R2) 5 (R1) 1 (P) 3 (R2) Note 1) Except VQZ1000 and metal seal.
As an equipment, calibration should be done by customer.
As an equipment, calibration should be done by customer.
Made to order options (see Page 55) Low temperatureresistant (XB6) resistant Modification of rod end auto switch Page P 8 P 1 7 P32 fechnical Data Auto switch guide P 4 6 P 3 8 ?
Made to order options (see Page 55) Low temperatureresistant (XB6) resistant Modification of rod end auto switch Page P 8 P 1 7 P32 fechnical Data Auto switch guide P 4 6 P 3 8 ?
Do not scratch or gouge the sliding portion of the piston rod or the outside threads of the outer tube by striking it with an object, squeezing it, or by forcefully wedging a set screw in it. Failure to observe this precaution could damage the seals, which could lead to oil leakage and malfunction.
6 M1L025-17B82076 C-7 P-6 M1L040-17B82078 C-9 P-8 4.7-10 Series ML1 Auto Switch Specifications Refer to p.5.3-2 for the details of auto switch.
When the cylinder is pressurized from port B, range E can be adjusted by regulating angle adjustment screw C. When the cylinder is pressurized from port A, range F can be adjusted by regulating angle adjustment screw D.
How to find the flow rate for air/ Flow rate formulas based on the air temperature of 20C For subsonic range where P + 0.1013 < 1.89 (P + 0.1013) Q = 226S P(P + 0.1013) For sonic range where P + 0.1013 1.89 (P + 0.1013) Q = 113S (P + 0.1013) Q : Flow rate [l/min(ANR)] S : Effective area (mm) P : Pressure drop P P (MPa) P: Upstream pressure (MPa) P: Downstream pressure (MPa) How to make
P p p 2-wire 12 V M9BW P P P p p Diagnostic indication (2-color indicator) Relay, PLC 24 V Grommet Yes 3-wire (NPN) 5 V, 12 V M9NA p p P p p IC circuit 3-wire (PNP) M9PA p p P p p 2-wire 12 V M9BA p p P p p Water resistant (2-color indicator) Grommet Yes 3-wire (NPN equivalent) 5 V A96 P P IC circuit Reed auto switch 2-wire 24 V 12 V 100 V A93 P P P P Relay, PLC No 5 V, 12 V 100
Note 2) Since the table is made of a magnetic substance, it could become magnetized if touched by a magnet, etc.
Divide the factor by the Compression Ratio. Then multiply the number by the actual length of pipe, in feet, then divide by 1000. This result is the pressure loss in PSI.
Divide the factor by the Compression Ratio. Then multiply the number by the actual length of pipe, in feet, then divide by 1000. This result is the pressure loss in PSI.
T I O N S ( I F A P P L I C A B L E ) XB5 _ For information on Bore Size, Rod and Rod Thread , please see How To Order Series NCA1 Replacement Parts.
Heavy Duty Stopper Cylinder RS2H Series 50, 63, 80 RoHS Weight Reduced by up to Reduced by up to Cylinder tube Shortened by up to Shortened by up to (RS2H63-30 stroke) Cylinder tube RSQ RSG RS2H RS2H RSH Replaceable just by loosening the set screw Stop the workpiece gently with adjustable shock absorber. Resistance value can be adjusted by rotating the adjustment dial.