Ionizer Use this as a guideline purpose only for model selection because the value varies depending on the material and/or size of a subject.
9 Snap ring Clip B 25, 32 only Stainless steel Stainless steel %6 @0 Cushion seal A Steel ball A Urethane Carbon steel @1 Steel ball B Same as cushion seal A Carbon steel %7 Cushion seal B Urethane except 20, 25 standard stroke @2 Tooth ring Stainless steel %8 @3 Cushion ring gasket A Bumper NBR Urethane @4 C type retaining ring for taper ring Carbon steel Same as cushion ring gasket A except
Dimensions: Universal Type Seal method: Sealant For R, NPT thread AS-FS AS-FSG Uni-AS-FS Applicable tubing O.D. d D3 W1 D1 Y L4 L3 M A L5 D2 L2 L1 T H (Width across flats) Metric Size [mm] Model d T H D1 D2 D3 L1 L2 L3 L4 L5 A M W1 Y Weight [g] Unlocked Locked Unlocked Locked AS231FS1-01-23 (S) 3.2 13.3 24 17.5 36 43.9 42.4 40.8 39.3 13.3 20 15 14 AS231FS1-01-04 (S) 4 8.2 13.9 25.1 AS231FS1
by the following formula: = 10 x mg = 20 x mg mg F = x a 2 x 10 x Workpiece weight 20 x Workpiece weight Even in cases where the coefficient of friction is greater than = 0.2, for reasons of safety, select a gripping force which is at least 10 to 20 times greater than the workpiece weight, as recommended by SMC.
0 Controller/Driver type*1 A 10 m* 11LEFS 11LEFS C 20 m* !
A (Part no.: ZS-46-A1) 20 20 45 30 2 5.2 30 34.6 19 5.2 14.7 47 9.6 The bracket configuration allows for mounting in four orientations.
the workpiece, select a model that can provide a gripping force of 10 to 20 times the workpiece weight, or more.
the workpiece, select a model that can provide a gripping force of 10 to 20 times the workpiece weight, or more.
Applicable to a wide range of applications. Pleated type has 3 times the filtration area of a cylinder. Filters are economical because they can be cleaned and repeatedly used. Main applications Please use 40 microns or less as a high-precision filter, and 74 microns or higher as a high-grade strainer. All types of gases and fluids, high-temperature fluids.
Applicable to a wide range of applications. Pleated type has 3 times the filtration area of a cylinder. Filters are economical because they can be cleaned and repeatedly used. Main applications Please use 40 microns or less as a high-precision filter, and 74 microns or higher as a high-grade strainer. All types of gases and fluids, high-temperature fluids.
mg F F Gripping force at least 10 to 20 times the work piece weight The "10 to 20 times or more of the work piece weight" recommended by SMC is calculated with the safety margin of a = 4, which allows for impacts that occur during normal transportation, etc. 2F mg Number of fingers and therefore, mg F 2 x With "a" as the safety margin, F is determined as follows: mg F = x a 2 x When
Applicable shaft type: Y Y = X = X = Long shaft side (mm) (mm) Long shaft side Long shaft side Y Y X X Size Size Body (B) Body (B) 10 10 1 to 14 1 to 14 1 to 14 1 to 14 Body (B) Body (A) Body (A) X = X = 15 15 1.5 to 18 1.5 to 18 1.5 to 18 1.5 to 18 Body (A) Y = Y = 20 20 1.5 to 20 1.5 to 20 1.5 to 20 1.5 to 20 Short shaft side Short shaft side 30 30 2 to 22 2 to 22 2 to 22 2 to 22 Short
If conditions (water splashes, time, temperature) beyond the normal ranges can be applied to the auto switch, use the auto switch in an environment where it will not be directly exposed to water splashes at a high temperature by installing a cover to protect the entire auto switch, as long as it is possible.
marks 3 to 8 or EA, EB ports should be taken as individual port using a block plate.
Provide a specific grounding as close to the unit as possible to minimize the distance to grounding. 0 V 0 V Power supply for control/input 24 V Power supply for control/input +24 V 4. Do not install a unit in a place where it can be used as a foothold. Applying any excessive load such as stepping on the unit by mistake or placing a foot on it, will cause it to break. 5.
-X5 is not added to an actuator model with a controller/driver part number suffix. Example) LEY25DB-100 for the LEY25DB-100BMU-R16N1D-X5 Stroke Model 30 50 100 150 200 250 300 350 400 450 500 Manufacturable stroke range [mm] LEY25 15 to 400 LEY32 20 to 500 Please consult with SMC for non-standard strokes as they are produced as special orders.
1 Compact Rotary Actuator Rack & Pinion Style Series CRQ2 Size: 10, 15, 20, 30, 40 Rotary actuator body serves as a flange.
B C L A B C Lead 20 10 5 2.86 20 10 5 Parameter *1,*2 Para.
In order to further improve stopping accuracy, the time from the stop signal to the operation of the lock should be shortened as much as possible. To accomplish this, use a device such as a highly responsive electric control circuit or solenoid valve driven by direct current, and place the solenoid valve as close as possible to the cylinder. 4.
In order to further improve stopping accuracy, the time from the stop signal to the operation of the lock should be shortened as much as possible. To accomplish this, use a device such as a highly responsive electric control circuit or solenoid valve driven by direct current, and place the solenoid valve as close as possible to the cylinder. 4.