JXCx-OMU0026 OFF 10Mbps P2-100 EtherNet/IP communication speed Orange LED is ON 100Mbps OFF Communication is not established. No data transmission. Green LED is ON Communication is established. No data transmission. P2-L/A Data transmission status Green LED is flashing Communication is established. Data transmission in progress. -33No.
EtherNet/IP communication connector EtherNet/IP communication connector (P1 and P2) specifications are shown below. Terminal Function Functional explanation 1 TX+ Sending (+) 1 2 TXSending (-) . . . . 3 RX+ Receiving (+) 4 5 8 6 RXReceiving (-) Shell 7 8 -43No. JXC-OMT0002-C 8.
Warning How to Find the Flow Rate (at air temperature of 20 ) Subsonic flow when (P2+0.100)/ (P1+0.100)>0.5 Q=240S P(P1+0.100) Sonic flow when (P2+0.100)/ (P1+0.100)0.5 Q=120S (P1+0.100) Q: Air flow ratedm 3 /min(ANR) S: Effective sectional area (mm 2 ) P: Differential pressure P1P2MPa P1: Upstream pressureMPa P2: Downstream pressureMPa Correction for different air temperatures Multiply
Q=226S P(P2+0.1013) Sonic flow : P1+0.10131.89(P2+0.1013) Q=113S(P1+0.1013) Q : Flow rate [ /min(ANR)] S : Effective area (mm2) P : Pressure differential (P1-P2) [MPa] P1 : Upstream pressure [MPa] P2 : Downstream pressure [MPa] When the air temperature is different, multiply the flow rate calculated with the above formula by the following coefficient for compensation. -20 1.08 -10 0 10 30
How to Find the Flow Rate (at air temperature of 20C) Subsonic flow when P1 + 0.1013 < 1.89 (P2 + 0.1013) Q = 226S P(P2 + 0.1013) Sonic flow when P1 +0.1013 1.89 (P2 + 0.1013) Q = 113S (P1 + 0.1013) Q: Air flow rate [l/min(ANR)] S: Effective sectional area (mm) P: Differential pressure (P1-P2) [MPa] P1: Upstream pressure [MPa] P2: Downstream pressure [MPa] Correction for different air temperatures
Maximum load current: 30mA The NPN and PNP digital monitor outputs can be set to function in one of three different ways: comparator mode hysteresis mode self-diagnostic mode when P1<P2 when P1>=P2 when P1=P2=0 The output is on whenever the outlet pressure is greater than P1 but less than P2. The output comes on once the outlet pressure reaches P1.
A B C D1 E F G M (Fine pitch) P2 MXQ6(L, A) MXQA-AS8-X2202 41.5 2.5 3 M3 x 12 18 5.8 8.3 M6 x 0.75 M3 x 6 MXQ8(L, A, C, CL) MXQ6B(L) MXQ12(L, A, C, CL) MXQ8B(L) MXQA-AS12-X2202 46.5 2.5 4 M3 x 12 24 7.1 10.4 M8 x 1 M4 x 8 MXQ16(A) MXQ12B(L) MXQA-AS16-X2202 51.5 3 5 M4 x 12 29.4 9.2 12.6 M10 x 1 M5 x 10 MXQ20(A) MXQ16B MXQA-AS20-X2202 58.5 4 6 M5 x 12 36 11.2 16.2 M12 x 1 M6 x 12 MXQ25(A)
1 Q=226S P(P2+0.1013) Sonic flow : P1+0.1013 1.89(P2+0.1013) Do not use in an explosive environment. 2 Q=113S(P1+0.1013) Q : Flow rate [ /min(ANR)] S : Effective area (mm2) P : Differential pressure (P1-P2) [MPa] P1 : Upstream pressure [MPa] P2 : Downstream pressure [MPa] Do not use in locations subject to heavy vibration and/or shock.
How to Calculate Flow (At an air temperature 20C) 1P1+0.1013<1.89(P2+0.1013) Q=226S P(P2+0.1013) Piping 2P1+0.10131.89(P2+0.1013) 1Completely flush (air blow) pipes before plumbing to remove dust. 2Clamping torgue: Q=113S(P1+0.1013) Q:Flow rate under standard conditions [ /min (ANR)] P1:Upstream pressure (MPa) P2:Downstream pressure(MPa) P:Pressure differential(P1-P2)(MPa) S:Effective area
Maximum load current: 30mA The NPN and PNP digital monitor outputs can be set to function in one of three different ways: comparator mode hysteresis mode self-diagnostic mode when P1<P2 when P1>=P2 when P1=P2=0 The output is on whenever the outlet pressure is greater than P1 but less than P2. The output comes on once the outlet pressure reaches P1.
Flat type with groove (UM) Bellows type with groove (BM) 32 40 50 63 80 100 125 32 40 50 63 80 100 125 ZP3EA-P1 V V V V ZP3EA-P2 V V ZP3EA-P3 V V V ZP3EA-P4 V V ZP3EA-P5 V V ZP3EA-P6 V e Holder t Pad Form/Diameter Part no.
[Accumulated output mode] Set each [P1]/[P2] (set value), referring to setting method of page 27. (When reversed output is selected, the main screen displays [n1]/[n2]).
External Pilot Piping of pilot port [12(P1), 10(P2)] P1 and P2 piping should be as follows according to the model. Caution Port VND0D VND02D 12(P1) External Pilot Bleed port 10(P2) Bleed port External Pilot Installing a silencer to the exhaust port and the bleed port is recommended for noise reduction and for dust entry prevention.
Pilot port piping 12(P1) and 10(P2) piping should be as follows according to the model () If the pilot air is not supplied, the valve position will not be held. Pressurize Port 12 (P1 ) or Port 10 (P2) when using the product. Installing a silencer to the exhaust port and the bleed port is recommended for noise reduction and for dust entry prevention.
P2, L5 RT3-3-1 S/S . P2, L5 RT3-1-3 S/S . P2, L5 RT1-3-1 S/S . P2, L5 X1 S/S . P3, L10 1 2 1 2 1/2 B Thd D A Thd C Hole Dia. Stainless Steel Threaded Parts Page & Part No. Line No. Page & Part No. Line No. D Line No.
Fixed orifice and variable throttle are available as a throttle for adjusting the pressure increase. (1, 1.5, 2) Output Pressure (P2) vs Time Graph Output P2 P1 P2 reaches half of P1, and then the main valve of the soft start-up valve turns on.
P2 = 1.5 x 0.5 0.024 x 15 = 0.39 MPa When restarting the regulator after leaving unused for a long period of time, starting pressure increases because rubber sticks to it. Applying the same pressure to P1 and P2 is recommended when restarting.
P2 = 1.5 x 0.5-0.024 x 15 = 0.39 MPa r Retraction The above values are for cases where the maximum payload found by the selection method is loaded. 0.2 0.1 100 200 300 Speed Adjustment Max. speed (mm/s) The data below illustrates the strokes controlled by the respective speed controllers. Gradually increase from a low speed to the desired speed setting.
Please check that each wire and cable is not broken. 6 Open the 3 (R) port. 7 Open the P2 port. 8 Input signal, and supply air to port 2 (A).
Warning Pilot port piping 12(P1) and 10(P2) piping should be as follows according to the model Standard () If the pilot air is not supplied, the valve position will not be held. Pressurize Port 12 (P1 ) or Port 10 (P2) when using the product. Vacuum pilot Installing a silencer to the exhaust port and the bleed port is recommended for noise reduction and for dust entry prevention.