Air Preparation Equipment Degrees of quality Max. particle diameter ( µ m) Min. pressure dew point ( ° C) Max. oil density (mg/m 3 ) International Standard ISO 8573-1: 1991 Degrees of Quality Japanese Industrial Standard JIS B 8392-1: 2000 Degrees of Qual It is recommended for future piping expansion that all piping ends should terminate with a T joint with plugs.
Contacts/Bulb gland Pressure Source Nil W Nil B C 1a1b (Standard) 2ab Contact Warning Enclosure Type A 20a (Standard) Type A 20b Type A 20c Bulb gland 1.
Detaching To detach a socket from a connector, pull out the lead wire while pressing the socket's hook with a stick having a thin tip (about 1 mm). If the socket will be used again, first spread the hook outward.
As a guide, refer to the proper tightening torques shown below.
The mist then coagulates to form a large drop, becomes separated from the compressed air, accumulates in case e, and is discharged through the drain valve. Meanwhile, the clean compressed air in housing w passes through flow hole A of body , it is reduced to a specified pressure by the pressure reducing valve, and is discharged from the OUT.
Bore size (mm) 32, 40 50, 63 80, 100 Bore size (mm) 32 40 50 63 80 100 Mounting bracket BT-03 BT-05 BT-06 (1) MB-L03 MB-L04 MB-L05 MB-L06 MB-L08 MB-L10 Foot A set of following stainless steel mounting screws is attached. (A mounting bracket itself is not attached. Please order it separately.)
E P A E Port direction Applicable valve model Exhaust type Side Side Side Side Bottom Side VS3114-00 Base Base Base Common 1 4 3 8 3 8 Accessory AXT338-17A Blanking plate (With gaskets and screw) How to order manifold VVS31 1 0 05 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
(A contact) Standard GXL-8F 3 wire N.O. (A contact) Varying frequencies GXL-8FI LXF LXS 3 wire N.C. (B contact) Standard GXL-8FB 3 wire N.C. (B contact) Varying frequencies GXL-8FIB 2 wire N.O. (A contact) Standard GXL-8FU 2 wire N.C. (B contact) Standard GXL-8FUB Switch specifications (SUNX Corporation) GXL-8F(I)(B) GXL-8FU GXL-8FUB Part no.
Bore size (mm) 32, 40 50, 63 80, 100 BT-06 Bore size (mm) 32 40 50 63 80 100 Mounting bracket BT-03 BT-05 (1) Foot MB-L03 MB-L04 MB-L05 MB-L06 MB-L08 MB-L10 A set of following stainless steel mounting screws is attached. (A mounting bracket itself is not attached. Please order it separately.)
Installing of the tube 1) Cut the tubing at a right angle. The tube must not have any cuts on its periphery. Use a tube cutter TK-1, 2, or 3. Do not use a pair of pliers, nippers, or scissors because they could result in an uneven cut or cause the tube to become flattened.
/40 800/50 XL1A25-60S-1 XL1A25-60S-2 XL1A25-60S-2 1 1 1 H5 AC100V 200/40 400/70 400/80 / AC200V 800/40 1600/80 1600/80 XLA-63-2 XLA-80-2 AC90240V XL1A25-60S-2 XL1A25-60S-3 1 1 H4 AC100V 400/100 600/150 / AC200V 1600/100 2400/150 XL1A25-60S-3 XL1A25-60S-2 1 2 H5 AC100V 600/130 800/180 / AC200V 2400/130 3200/180 1[W] 216 PTC 200V PTC 200 150 100V PTC 0 5 10
.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com VR Model VH Flow characteristics (2) 1 4/2 (P A/B) 4/2 5/3 (A/B EA/EB) C [dm3/(sbar)] Cv Type of actuation Port size Pilot port size b Cv b C [dm3/(sbar)] Valve model Pilot VHS Body ported Body ported Base mounted Base mounted (With sub-plate) VZA212
B C A B C A B C A B C Lead 12 6 3 12 6 3 20 10 5 16 8 4 Point table No.1 Initial value Recommended value Home position return acceleration time constant (msec) *5 0 600 300 150 600 300 150 1000 500 250 800 400 200 Different from the initial value. *5.
A bit can have a value of 1 or 0. Branch A bus topology term used to describe a drop off the trunk line. Bus A group of lines used for data transmission or control. Bus Topology The physical layout of the nodes and the interconnecting physical media. Bus line Any type of wires that carry data from node to node.
Aluminum alloy 1728 3 Port 3 Position Valve VEX3 Series Working Principle Fig. (1) A R Fig. (2) Closed center Fig. (3) P A 3(R) 3(R) 3(R) 2(A) 2(A) 2(A) 1(P) 1(P) 1(P) This is a 3-port switch valve in which the shaft 7 extending from the driving piston 3 opens/closes a pair of poppet valves 6.
T-interface (T) M5 x 0.8, 1/8, 1/4, 3/8, 1/2 Factory mounting of a piping adapter on the AC models is available as a special order. Using a T-interface facilitates the redirection of air flow.
MA a CHM A MA a Cushion adjustment screw Air release R (max.)
C C RHC D D Note) Be sure to use a flat washer for the type A mounting.