Electric Actuator To prevent danger and damage due to a breakdown or malfunction of these products, which may occur at a certain probability, a backup system should be arranged in advance by using a multiple-layered structure or by making a fail-safe equipment design, etc. 13. Avoid heat radiation from strong heat sources, such as direct sunlight or a hot furnace.
A + A' A' w After piston seal H has passed air passage A, air is exhausted only through A'. The section marked with slanted lines becomes a cushion chamber, and an air cushion effect is achieved. A A' A' e When air is supplied for the piston extension, the check valve opens and the piston extends with no delay.
When the product is mounted so that the exhaust port side will be against a wall, use a spacer to secure a clearance of at least 0.039 inch (1 mm). (Fig. 1) For the single unit, PV port and PD port are oriented downward. When it is installed on a working table, use a bracket for single unit (Fig. 2) or secure a space for piping underneath the ports.
Connection of piping to products When connecting piping to a product, refer to its instruction manual to avoid mistakes regarding the supply port, etc. 6. Steam generated in a boiler contains a large amount of drainage. Be sure to operate it with a drain trap installed. 7.
and V124(A) cannot be mounted to the same manifold.
R1 ND MM ND MM R1 MM E1 ND NX1 A U1 R2 H Z E1 NX U1 L1 A A NX A1 (Min.) A1 U1 L1 Applicable bore size 20 25, 32 40 MM L1 NX NDH10 R1 E1 A1 U1 A A H MM NDH10 NX1 U1 R2 Y Z Part no.
Dont use a wrench on push-to-connect end. 2 2 Cut tubing square with a clean 90 edge Dont use excessive tube angle cut which can lead to leakage or breaking. 90 90 3 3 Use SMC Tube Cutters Dont use dikes, a knife, a saw or a dull tool to cut the tubing.
the tube surface of a closely mounted built-in strong magnet type cylinder by 30 mm or more. 3) When a built-in strong magnet type cylinder and a cylinder with a general-purpose auto switch are closely positioned, separate the cylinder tubes 50 mm or more. 4) Separate a general-purpose auto switch from the tube surface of a closely mounted built-in strong magnet cylinder by 50 mm or more
model with a longer l dimension, be sure to choose a sufficiently large bore size.
D-F9WV D-F8 Model A B C D E A B C D E A B C D E A B C D E A B C D E A B C D E A B C D E A B C D E 18.5 31 6.5 20.5 41 8.5 20.5 33 4.5 17 20.5 31 4.5 15 20.5 41 4.5 15 20.5 51 4.5 35 22.5 43 6.5 27 22.5 33 6.5 17 22.5 43 6.5 27 22.5 53 6.5 37 MIW12-12D MIW20-20D 6 4 4 2 18.5 29 6.5 20.5 31 8.5 MIS12-10D MIS20-10D 4 2 6 4 2.5 4 18.5 39 6.5 20.5 41 8.5 MIS12-20D MIS20-20D 6 4
A B C A B A B A B A B 15A 20A 25A Note 1) For each piping diameter for each body size, the second and later numbers or symbols indicate reducing.
SGH(A)32-7020 SGH(A)42-7025 SGH(A)13-3010 SGH(A)23-3015 SGH(A)33-3020 SGH(A)43-3025 SGH(A)13-7010 SGH(A)23-7015 SGH(A)33-7020 SGH(A)43-7025 3/8 7.5 42 (1.8) 1.4 1.5 1/2 9.4 65 (2.7) 2.4 2.6 7 MPa 2-port 3/4 12.4 112 (4.7) 4.7 5.3 1 15.4 155 (6.5) 6.6 7.2 3/8 9.4 50 (2.1) 56 (2.3) 1.6 1.7 11 1/2 10.5 55 (2.3) 73 (3.0) 1.6 1.7 3 MPa 15 3/4 12 90 (3.8) 92 (3.8) 2.6 2.8 17 1 15.2 135
MGPM MGPL/A MGPM MGPL/A MGPM MGPL/A MGPM MGPL/A MGPM MGPL/A MGPM MGPL/A MGPM MGPL/A MGPM MGPL/A MGPM MGPL/A 12 16 20 25 32 40 50 63 80 100 (1Nm = 0.74 ftlb) 5 Compact Guide Cylinder Series MGP High Precision Ball Bushing/MGPA Non-rotating Accuracy of Plate Caution + Positioning accuracy for pin hole on the plate Dispersion of dimensions when machining each component will be accumulated in
10 A 180/200 W 50/60 Hz 220 W 0.01 m (99.9% filtration efficiency) Particles of 0.3 m or more: 3.5 particles/L [ANR] or less Heater operation, PID control Singlephase 200 VAC (50/60 Hz) 2.1 A 5 A Singlephase 230 VAC (50/60 Hz) 2.1 A 5 A Singlephase 100 VAC (50/60 Hz) 9.4 A 15 A Singlephase 200 VAC (50/60 Hz) 4.8 A 10 A Singlephase 230 VAC (50/60 Hz) 4.8 A 10 A Power supply Note 4) Operating
Double acting PA PA B A PB B A With by-pass Suck back valve Manual Operation-Series LVH N.C. Double acting P PA PA Locking and non-locking types available B A B A PB B A Integral fitting type/Threaded type Manifolds Main applications and fields For shut off For air bleeding N.C.
To release residual pressure, select a model with a back flow mechanism.
[Check valve] A check valve is a safety device intended to prevent reverse flow. The AP 64 is a unique design with only one moving part in the gas stream, an O-ring. It is a springless design, free of springs and poppets. [Vacuum generator] A venturi device that creates vacuum by flowing gas through a nozzle.
When a surge generating a load such as a relay or solenoid is directly driven, use a type of switch with a built-in surge absorbing element. 4. Since the type of fluid varies depending on the product, be sure to verify the specifications. The switches do not have an explosion proof rating. To prevent a possible fire hazard, do not use with flammable gases or fluids. 5.
To release residual pressure, select a model with a back flow mechanism.