LVQ T) PB View Z Dimensions (N.O. valve, double acting valve) (mm) A B C D M N T U V Model LVQ2 S-S07-2 LVQ3 S-S11-2 LVQ4 S-S13-2 LVQ5 S-S19-2 LVQ6 S-S25-2 2 1 25.5 46 31.5 58 7 15 35.3 10.6 7 2 1 23.5 47 29.5 59 7 15 36.9 16.5 10 2 1 23.5 47 29.5 59 7 20 37.9 22 2 1 35 70 41 82 7 20 64 25 17 2 1 35 70 41 82 7 20 66 32 17-5-81 20 Series LVQ Fittings and Special Tools Fittings Changing tubing
10-S005 FN41l2l-20-S005 20 m FN11lll-10-S020 FN41l2l-20-S020 100 100 80 80 Filtration efficiency (%) Filtration efficiency (%) 60 60 40 40 20 20 0 0 10 5 20 50 75 25 20 35 65 90 Particle diameter (m) Particle diameter (m) 3 Low Maintenance Filter Series FN1/FN4 Blocking Characteristics (Repeatability) P Fluid: Potable water P Supply pressure: 0.2 MPa P Flow rate: 20 l/min P Test dust: AC
Connection port location B Basic type Nil E Side ported Axial ported Free mount type Available with side ported only, when equipped with auto switch unit. 20 90 S M SUB Without auto switch 20 90 S D SUB L T79 M With auto switch Number of auto switches S Nil 1 pc.
(When the value at every 0.01deg.C is input, it is rounded off.)
(Values at the initial period) Vibration rerisutance: No malfunction occurred in a one-sweep test between 45 and 2,000 Hz. Test was performed at both energized and be-energized states in the axial derection and at the right angles to the main valve and armature.(Values at the initial period) 10 - 4.
No.PS-OMM0005-J PRODUCT NAME Digital Pressure Switch MODEL / Series / Product Number ZSE10(F) ISE10 Table of Contents Safety Instructions 2 Model Indication and How to order 9 Summary of Product parts 11 Definition and terminology 12 Mounting and Installation 15 Installation 15 Piping 17 Wiring 18 Internal circuit and wiring example 19 Pressure Setting 20 Measurement mode 20 Function Setting
Prohibited way of using the valve which is written at "Precautions" section in this operation manual was carried out excluding above-mentioned.
AD27-A I.D. 2.5 (3/32") at min., Length 5m (200") at max. AD37, 47(N)-A I.D. 4 (3/16") at min., Length 5m (200") at max. AD38, 48(N)-A: I.D. 6.5 (1/4") at min., Length 5m (200") at max. Air Source WARNING Use clean air. Compressed air containing chemicals, organic solvent, synthetic oil or corrosive gas may lead to cause breakage of parts or malfunction.
Add the "" symbol at the beginning of part numbers for solenoid valves, etc., to be mounted.
mA DC, 0 to 20 mA DC (Sink type) Input signal Voltage type Current type Voltage type 0 to 5 VDC, 0 to 10 VDC 500 7 or less Input impedance 6 to 6.5 k7 (at ordinary temperature) 1 to 5 VDC (Output impedance: Approx. 1 k7) Output accuracy: p6% or less (Full span) Analog output 4 to 20 mA DC (Sink type) Load impedance: 250 7 or less Note 5) Output accuracy: p6% or less (Full span) Output signal
End plate: Connected at EX600 Manifolds D side, incorporating the power supply connection. Solenoid valve manifold: An assembly of solenoid valves.
AXT100-20-2-05 AXT100-20-2-06 AXT100-20-2-01 AXT100-20-2-02 AXT100-20-2-03 AXT100-20-2-04 Clip Circuit with light PR plate qChanging the piping direction from in-line to perpendicular (port on the valve) is possible on the VQZ100 series. Follow the steps below to change piping direction: Remove the fitting clips that hold the fitting and port plug in place.
AXT100-20-2-05 AXT100-20-2-06 AXT100-20-2-01 AXT100-20-2-02 AXT100-20-2-03 AXT100-20-2-04 Valve Mounting VS After confirming the gasket is correctly placed under the valve, tighten the mounting screws with the appropriate torque listed below.
Use to connect tubes at right angles. P. 6 KJY P. 4 KJL P. 8 KJR Gasket/10-32 UNF seal on thread Part no.: M-10/32G Material: Stainless steel 304, NBR Precautions Be sure to read before handling.
Mount an auto switch at the center of the operating range. In the case of 2-color display auto switch, mount it at the center of the green LED illuminating range. Adjust the mounting position of the auto switch so that the piston stops at the center of the operating range. (The mounting position shown in the catalog indicates the optimum position at stroke end.)
The port exhaust specification for back pressure should be 0.005MPa (5kPa) at maximum., Exhaust resistance is generated with some piping bore sizes and piping lengths. For tube ID 4, as a guideline, it is recommended to make the piping length 1000mm at maximum, although it varies depending on the condition of the equipment at the end.
Note 3) This means that the element does not break at 0.5 MPa.
A per branch: 20 m or less At 1.0 A per branch : 16 m or less At 1.5 A per branch : 10 m or less Branch cable length Insulating cap Brown Black White Blue 1: Input terminals are not isolated from Power source. 2: Do not connect outside Power source to Input and Output terminals.
AD27-A I.D. 2.5 (3/32") at min., Length 5m (200") at max. AD37, 47(N)-A I.D. 4 (3/16") at min., Length 5m (200") at max. AD38, 48(N)-A: I.D. 6.5 (1/4") at min., Length 5m (200") at max. Air Source WARNING Use clean air. Compressed air containing chemicals, organic solvent, synthetic oil or corrosive gas may lead to cause breakage of parts or malfunction.
Double vane CRB1BW10-lD CRB1BW15/20/30-lD/Dimensions below are based on size 20. /Dimensions below shows the middle locations of pressurization to A port or B port.