Refrigerated Thermo-chiller There are many types, including perfluoropolyether (PFPE), perfluorocarbon (PFC), hydrofluoropolyether (HFPE), and hydrofluoroether (HFE), but they share the characteristic of high electrical insulation properties, and grades can be selected with appropriate fluidity even at low temperatures, such as 100C, and high temperatures, such as 200C and above.
Although the variation in the operating range differs with the cylinder on which the auto switch is mounted, a temperature change of 100C will roughly result in the maximum of 20% reduction in the overall operation range.
The packing class has been revised to adopt heat resistant materials for using it at a high temperature of up to 100C.
There are many types, including perfluoropolyether (PFPE), perfluorocarbon (PFC), hydrofluoropolyether (HFPE), and hydrofluoroether (HFE), but they share the characteristic of high electrical insulation properties, and grades can be selected with appropriate fluidity even at low temperatures, such as 100C, and high temperatures, such as 200C and above.
Controller Specifications LC7R-K11A LC7R-K12A Model Regeneration method Heat exchange method based on resistance Regenerative resistance capacity 40W Regenerative operation voltage 180V 380V Regenerative absorption unit Regenerative voltage input mis-wiring protection Over current protection, Overheating protection (Normally closed, Radiator sensor OFF at 100C) Protective circuit To PLC,
Although the variation in the operating range differs with the cylinder on which the auto switch is mounted, a temperature change of 100C will roughly result in the maximum of 20% reduction in the overall operation range.
(Equivalent to IP44) 90C 47C (50C) or less Splashproof/ Low jetproof type (JIS C 0920) 35C (40C) or less 100C Note) ( ) For IF32 To protect the microswitch, ambient temperature must be lowered when the fluid temperature exceeds 70C.
) Steam system (Boiler water) Steam system (Condensate) Insulation oil Parachloroetylene Brake oil Water (up to 99C) Ethyl alcohol Ethylene glycol Caustic soda (25% ) Gas oil Silicon oil Fuel oil (up to 60C) Fuel oil (up to 100C) Steam system (Boiler water) Steam system (Condensate) Insulation oil Naphtha Parachloroetylene Brake oil Water (up to 99C) Note) If using for other fluids, please
Liquid dripping: 0.02 to 0.06 cm3 at each removal Aeration: 0.1 to 0.2 cm3 at each removal VMG Socket valve Plug valve Non-greased specifications (standard) O-ring: Fluorine coated Sliding parts of plug and socket: Plated with fluorine-contained material Allows smooth installation and removal even without grease Fluid: Water, Air Operating temperature range: 5 to 100C Note) Do not use
Regenerative voltage input mis-wiring protection Over current protection, Overheating protection (Normally closed, Radiator sensor OFF at 100C) Protective circuit Danger 1. Contact SMC if the connected controller power supply voltage will be 110VAC or 220VAC, as this may cause fire or malfunction.
New Products Guide 1 Directional Control Valves Actuators Vacuum Equipment CAT.E00-6A INDEX New Products Guide 1 Directional Control Valves 5 Port Solenoid Valve Fieldbus System (For Input/Output) 2/3 Port Mechanical Valve Series SY3000/5000/7000 Series EX600 Series VM100/200 P .6 P .264 P .322 Actuators Foot Pedal Type 5 Port Mechanical Valve XT34-60/67 Air Cylinder Air Cylinder Series CJ2
A.7A0: Heat Sink Overheated (Detected when the heat sink temperature exceeds 100C.) Check the accumulated load ratio (Un009) to see the load during operation, and the regenerative load ratio (Un00A) to see the regenerative energy processing capacity. Excessive load or operation beyond the regenerative energy processing capacity. Reconsider the load and operating conditions.
Controller Specifications LC7R-K11A LC7R-K12A Model Regeneration method Heat exchange method based on resistance Regenerative resistance capacity 40W Regenerative operation voltage 180V 380V Regenerative absorption unit Regenerative voltage input mis-wiring protection Over current protection, Overheating protection (Normally closed, Radiator sensor OFF at 100C) Protective circuit To PLC,
A.7A0: Heat Sink Overheated (Detected when the heat sink temperature exceeds 100C.) Check the accumulated load ratio (Un009) to see the load during operation, and the regenerative load ratio (Un00A) to see the regenerative energy processing capacity. Excessive load or operation beyond the regenerative energy processing capacity. Reconsider the load and operating conditions.