Precision Regulator Troubleshooting 13 8. Assembly drawing 14 -1- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Mounting Mounting Warning (13) The handle of this product is attached only by press fitting. (ASB series only) Excess torque may break the product. The table below shows the maximum allowable torque of the handle. (14) Refer to the table below for the applicable operating torque and recommended driver of the needle.
version V.1.1 Communication speed COM2(38.4kbps) Minimum cycle time 2.3 ms Process data length Input Data: 2byte, Output Data: 0 byte Process data Bit Data Description 0 OUT1 0 OFF 1 ON 1 OUT2 0 OFF 1 ON 0 normal 1 error Set at index 0x03EB 2 Diagnosis Pressure Unsigned 13bit *: Refer to the table below(Unit specification and pressure measurement value (PD)) 315 measurement value Bit 15 14 13
This may damage the pressure sensor, leading to malfunction. 25.5 Brown OUT(+) Load PS1000/PS1100/PS1200 + Main circuit of switch 12 to 24 VDC AIRCHECKER + PS1000-R06L 13 PRESS. -0.10.45MPa {-14.6kgf/cm2} MADE IN JAPAN G Thank you for purchasing the SMC PS1000/PS1100/PS1200 Series Air Checker: Electronic Pressure Switch.
Troubleshooting 13 11. Definitions and Terminology (Supplementary Explanation) 15 -1No.EX-OMV1026-B 1.
For applications such as mounting a valve on a control panel, incorporate measure to limit the heat radiation so that it is within the operation temperature range. 13. Do not disassemble the product of make any modifications, including additional machining. 7. Release of residual pressure For maintenance purposes install a system for releasing residual pressure.
Isolate the valve and re-tighten the bolts. (13) (14) Lessen the oil supply amount to the degree that oill does not spout out of the exhaust port [3(EB), 5(EA), PE port]. *In the case of N.O. specification, 1(P) port. (15) Supply specified pressure to X port.
Buzzing Abrasion armature (AC coil Fall of power supply voltage 13 No.VP300-OMM0002-A Remedy No. Remedy Regulate voltage, so that the voltage at the time of the operation becomes specifications range. Re-wire positively. Replace part. Replace part or re-wire positively. Replace valve.
) DCAC (7) 14 No.VEX-OMY0001 o. (1) (2) (3) (4) (5) 1 ISO VG 32 (6) (7) (8) (9) (10) (11) (12) () (13) (14) ()() 15 No.VEX-OMY0001 C 2020.6 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer
(1) (2) (3) 2(A)3(R)() (4) (5) 3(R) (6) 2(A)() (7) (8) (9) (10) (11) (12) 1 (ISO VG32) (13) 3(R) (14) (15) (16) (17) (18) (19) (20) (21) (22) 1. 2. 3. 4. 5. 6. 7. * 12 VEX-OMV0001 : VW 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com Note: Specifications are subject to change without prior notice
HW HW Diagnosis information Diagnosis information of the SI unit is composed of 6 bytes standard diagnosis information and 7 bytes SI unit status information, 13 bytes in total, as specified in PROFIBUS DP. When the SI unit is in a non-standard state, it will send an error message to the master as diagnosis information, and light up the DIA display.
)15.5(13)18.5(16)34.5(32)50.5(48)83.5(81)98.5(96)8
)15.5(13)18.5(16)34.5(32)50.5(48)83.5(81)98.5(96)8
Seal Kit List (12, 13, 18 and 20 are not included in the seal kit. Order them as required with by individual part numbers.) Description Qty.
Assembly of a piston and a seal (KSYP-13). Note 2) Check valve assembly is applicable for a regulator with backflow function (AR20K to AR60K) only. Assembly of a check valve cover, check valve body assembly and 2 screws Options/Part No.
6 6 11.8 11.6 11 11.6 44.8 6.3 19.6 31.7 13.7 13.7 AQ240F-07-07 AQ240F-07-00 13.7 15.4 6.2 40.7 8 10.0 1/4" 1/4" 12 6 12 40.7 6.2 15.1 27.3 13.7 13.7 AQ340F-07-07 AQ340F-07-00 16.8 20.3 7.1 52.2 13 11.8 1/4" 1/4" 13.2 11 13.2 52.2 7.1 20.0 33.1 16.8 13.7 557
(N) EPDM seal Bore size (mm) Rod size (mm) Piston area (mm2) Operating direction Operating pressure (MPa) For clean room specifications, refer to Pneumatic Clean Series catalog. 0.7 0.6 0.5 0.4 0.3 0.2 40 34 29 23 17 11 OUT IN 57 6 3 29 25 21 17 13 8 42 Standard Stroke 71 61 51 40 30 20 OUT IN 101 8 4 53 45 38 30 23 15 75 Model Standard stroke (mm) 158 136 113 90 68 45 OUT IN 226 12 6 10,
MK-A012 MK-A016 Bore size (mm) 12 16 20 25 32 40 50 63 12 70 87 16 100 123 20 250 290 25 280 320 32 500 525 40 595 640 50 1100 1350 63 1520 1805 Clamp bolt, Hexagon socket head cap screw, Hexagon nut, Spring washer MK-A020 MK-A032 Additional Weight MK-A050 Unit: g 63 17 46 25 350 531 50 7 46 13 350 345 32 7 21 5 200 166 40 6 21 7 200 198 25 7 10 3 100 153 12 13 16 32 20 6 10 2 100
(mm) a = Internal cross section of piping [mm] T 0425 T 0604 TU 0805 T 0806 1/8B T 1075 TU 1208 T 1209 1/4B TS 1612 3/8B T 1613 1/2B 3/4B 1B 4 2.5 4.9 QC = Air consumption required for one reciprocation of Mini-Rotary Actuator [l (ANR)] 6 4 12.6 8 5 19.6 8 6 28.3 6.5 33.2 10 7.5 44.2 12 8 50.3 12 9 63.6 9.2 66.5 16 12 113 12.7 127 16 13 133 16.1 204 21.6 366 27.6 598 Air Consumption
12 14 6 25 8.5 75 39 19 19 39 64.9 73.5 49.5 39 M10 x 1.5 12 20 LD LW MM M N L P PA PB Q QW R T TA TB W WA WB Y Z Model CYP15 5.6 69 M4 x 0.7 6 4.5 67 M5 x 0.8 25 60 105 48 45 23 13 18 69 32 17 2.5 118 CYP32 8.6 115 M6 x 1 8 7.5 90 Rc 1/8 50 100 138 87 79.5 29 17 22 115 46 27 3.5 155 Note 1) These dimension drawings indicate the case of piping port position "Nil".