Series MXP/MXPJ6 11- ø6, ø10, ø12, ø16 22- Air Slide Table A A Solid state auto switch D-M9B, D-M9N Reed auto switch D-A93 (mm) (mm) Stroke (mm) 20 41 29 47 35 Stroke (mm) 20 45 25 51 31 Auto switch operating range Auto switch operating range 15 40.5 20.5 Model Model 25 50.5 30.5 30 59 39 10 35 15 25 46.5 34.5 30 55 43 10 31 19 15 36.5 24.5 A B A B A B A B A B A B 11-/22-MXP10 11-/22-MXP10 11-/22-MXP12 11-/22-MXP12 3 5 11-/22-
Operate the piston within a range such that collision damage will not occur at the end of the stroke. When a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc.
HRX-OM-Q026-V Operation Manual Installation Operation Original Instructions Thermo Chiller HRSH Series HRSH100-A-20HRSH100-A-40HRSH100-A-20-S HRSH150-A-20HRSH150-A-40HRSH150-A-20-S HRSH200-A-20HRSH200-A-40HRSH200-A-20-S HRSH250-A-20HRSH250-A-40HRSH250-A-20-S HRSH300-A-20HRSH300-A-40HRSH100-W-20HRSH100-W-40HRSH100-W-20-S HRSH150-W-20HRSH150-W-40HRSH150-W-20-S HRSH200-W-20HRSH200-W-40HRSH200
-wire 12 V F5BA1 F59F 5 V, 12 V 4-wire (NPN) IC circuit IC circuit IC circuit Diagnostic output (2-color indicator) A96 A93 A90 100 V 100 V or less 100 V, 200 V 200 V or less 5 V 3-wire (NPN equiv.)
12 V 3-wire (PNP) 24 V Grommet 12 V 2-wire 100 V, 200 V Reed auto switch Solid state auto switch 3-wire (NPN) Terminal conduit 12 V 2-wire 3-wire (NPN) Relay, PLC IC circuit Yes 5 V, 12 V Diagnostic indication (2-color indication) 3-wire (PNP) 2-wire 24 V 12 V Grommet 3-wire (NPN) 5 V, 12 V 3-wire (PNP) Water resistant (2-color indication) 2-wire 12 V 4-wire (NPN) 5 V, 12 V IC circuit
For a facility having a large installation area (that can vent the air naturally): Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2. For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level.
Pad Bellows Pad For a workpiece that does not have a space for a buffer, or for a workpiece with a diagonal surface. Caution Guide for drop prevention If multiple pads are used for transporting a flat object with a large surface area, properly allocate the pads to maintain balance.
Reset (RES) Keeping RY(n 1)A or RY(n 3)A (RES) ON for 50ms or longer RY(n 1)A RY(n 3)A 1 allows an alarm to be deactivated. Some alarms cannot be deactivated by Reset RY(n 1)A or RY(n 3)A (RES). (Refer to section 10.4.1.) If RY(n 1)A or RY(n 3)A (RES) is turned ON with no alarm occurring, the base circuit will not be shut off.
Note 2) When mounting a cylinder with a stroke over 100mm, use the section A mounting threads.
Note Ground the FG terminal with a ground resistance of 100 or less. The connector for DeviceNetTM ( ) that is used to connect to the DeviceNetTM Fieldbus interface connector (BUS) 6 DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Danger: 1 bus line. A. Dual power supplies B.
Note 2) Please contact SMC for details. 1 (100 V) 2 (200 V) 3 (110 V) 4 (220 V) 7 (240 V) 8 (48 V) 5 (24 V) 6 (12 V) AC Operating Fluid and Ambient Temperature DC Operating fluid temperature (C) Ambient temperature (C ) Temperature conditions Power source Water (Standard) Air (Standard) Oil (Standard) (D.E.N.P) (D.N) (3) (3) High temperature water High temperature oil 99 100 60 40 40 60
A A function of the Pressure switch to automatically setup pressure just by having equipment hold and release a workpiece via vacuum adsorption. This function is used in an application where vacuum adsorption of a workpiece needs to be confirmed with a Pressure switch.
(Example: If the Pressure switch with output impedance of 1k is connected to the A/D converter to detect the analog output of 5V, the detected voltage by the A/D converter becomes 5(V) 1(M)/(1(k) + 1(M)) 4.995(V), and there is an error of approximate 0.005 V.) Output impedance P Peak hold mode Shows the maximum pressure reached at that moment.
Applicable Stroke Table V: Standard Stroke [mm] Model 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000 1100 1200 LEFS25 V V V V V V V V V V V V V V V V LEFS32 V V V V V V V V V V V V V V V V V V V V LEFS40 V V V V V V V V V V V V V V V V V V V V * Please consult with SMC for non-standard strokes as they are produced as special orders.
(full span/full scale) This means "full span" or "full scale", and indicates varied analogue output range at rated value.For example, when analogue output is 1 to 5 V, F.S.=5[V] 1[V]=4[V]. (Reference: 1%F.S. = 4[V] 1% = 0.04[V]) I Instantaneous flow The flow passing per unit of time. If it is 10 L/min, there is a flow of 10 L passing through the device in 1 minute.
piston and a gasket (KSYP-13) type assembly.
Designation Description 1 FG Function earth 2 0 V 0 V for solenoid valve 3 24 V +24 V for solenoid valve 4 SI0 V for SI unit operation 5 SI+ +24 V for SI unit operation The power supply connector included as an accessory can be used to supply the power. Applicable wire for the power supply connector is AWG24 to AWG16 (0.2 to 1.5 mm2).
Y69A Y7PV Y69B Y7NWV Y7PWV Y7BWV 100 V 24 V 12 V Z73 Y59A Y7P Y59B Y7NW Y7PW Y7BW 3-wire (NPN) 2-wire Relay, PLC 5 V, 12 V IC circuit 3-wire (PNP) 2-wire 12 V Relay, PLC 24 V Grommet 3-wire (NPN) 3-wire (PNP) Diagnostic indication (2-color indication) IC circuit 5 V, 12 V 2-wire 12 V Lead wire length symbols: 0.5 mNil (Example) Y59A 3 m L (Example) Y59AL 5 m Z (Example) Y59AZ Since
Option V Option V is a dryer with a timer controlled solenoid valve type auto drain.