Programless controller (with stroke study) Step motor (servo 24 VDC) C c OFF OFF OFF ON OFF D d OFF OFF OFF OFF ON E E OFF OFF OFF OFF OFF The control power supply turn off Turn on the power again When multiple alarms in alarm groups A to D occur, the relevant OUT0 to OUT3 will be ON.
Screwdriver 5 to 6 Switch mounting screw M2.5 X 4 l Hysteresis Auto switch Switch operating position (ON) Switch reset position (OFF) Max. hysteresis mm Auto switch D-F9BAL D-F9N(V) F9B(V) ON: Red light emitting diode Model ON: Green light emitting diode Note) Use a screwdriver with a grip diameter of 5 to 6mm to tighten the auto switch mounting screw.
Note) Output -27 and -67 only Internal Circuits and Wiring Examples Output -27 Output -43 2 settings NPN open collector 2 outputs Max. 30 V, 80 mA, Residual voltage 1 V or less Fixed setting NPN open collector 1 output + PNP open collector 1 output (The pressure set point for switching the output signal is common to NPN and PNP.)
Stations 02 03 2 stations 3 stations Station 3 2 1 D side U side 20 20 stations Note) Maximum of 20 stations Electrical entry Grommet/Plug lead C How to Order Valves S070 A 5 B G Electrical entry Body type Body type Base mounted with clips G C Grommet Plug lead with light/surge voltage suppressor Symbol A Coil voltage Power consumption Pressure specification Flow rate 5 6 V S R 24
Operating temperature 32 to 104F (0 to 40C) Material Conductive nylon + Flame resistant nylon (Equivalent to UL-94 Standards V-0) Surface resistance 104 to 107 Hardness Shore D 48 Note 1) Refer to the burst pressure characteristics and operating pressure curve for other temperatures. Avoid abnormal temperature rises due to adiabatic compression.
as standard) Outdoor installation IPX4 (400 V as standard) HRS100/150 Standard type 1.0 5 to 35 V V (400 V as standard, 200 V as an option) HRSH090 Inverter type 0.1 5 to 40 V Indoor use (Only 200 V as an option) (400 V as standard, 200 V as an option) Outdoor installation IPX4 HRSH Inverter type 0.1 5 to 35 V V V V V (Only 200 V as an option) 73 Circulating Fluid Temperature Controller
Applicable cable of the power supply connector Cable cross section Single wire, stranded wire 0.2 mm2 to 2.5 mm2/AWG24 to 12 Power supply connector for solenoid valve Terminal Wire colour Connection 24 V For solenoid valve +24 V 0 V For solenoid valve 0 V Note Wiring should be carried out with the power supply turned off.
Switches P: Operating pressure (PSI) V: Speed (inch/s) Stroke (inch) Mode of operation (horizontal, inclined, vertical) Mode of operation Note 1) Inclined operation Vertical operation Horizontal operation Review of load weight and operating pressure W Lo Guide First tentative bore size determination F1 D 1.6 x P First tentative bore size determination F2 D 1.6 x P First tentative bore size
Refer to 4.3.2 Setting and checking,5.3.2 Setting and checking. 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Do not connect any wire to other PIN numbers.
Refer to 4.3.2 Setting and checking,5.3.2 Setting and checking. 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Fig 3.3-2 RS-232C connector connection 3.3 Connected explanation HRSH Series 3-2 HRX-OM-R028 Chapter 4 MODBUS communication function Chapter 4 MODBUS communication function MODBUS protocol is a communication protocol developed by Modicon.
Single unit Note 1) Port exhaust B Ejector system t Pressure Sensor/Digital Pressure Switch for Vacuum Specifications Common Silencer exhaust Pressure sensor C Type Pressure range [kPa] Specifications Symbol P 0 to 101 Analog output 1 to 5 V Pressure sensor For manifold T Analog output 1 to 5 V 100 to 100 Individual port exhaust A B C D E F H J K Q R S Unit selection function Note 9) NPN
Refer to 4.3.2 Setting and checking,5.3.2 Setting and checking. 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Do not connect any wire to other PIN numbers.
Refer to 4.3.2 Setting and checking,5.3.2 Setting and checking. 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Do not connect any wire to other PIN numbers.
Refer to 4.3.2 Setting and checking,5.3.2 Setting and checking. 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Do not connect any wire to other PIN numbers.
Tightening Torque for Auto Switch Mounting Screws(Nm) Auto switch model Tightening torque D-M9(V) D-M9W(V) D-M9A(V) D-P3DWA 0.05 to 0.15 The indicator light may turn on when the tip of the screwdriver is close to the auto switch mounting screw. This is not a malfunction.
V as standard) Outdoor installation IPX4 (400 V as standard) HRS100/150 Standard type 1.0 5 to 35 V V (400 V as standard, 200 V as an option) HRSH090 Inverter type 0.1 5 to 40 V Indoor use (Only 200 V as an option) (400 V as standard, 200 V as an option) Outdoor installation IPX4 HRSH Inverter type 0.1 5 to 35 V V V V V (Only 200 V as an option) 195 Thermo-chiller Basic Type HRSE Series
This wiring is common in each mode. (1) Using 3-phase 200 V AC to 240 V AC power supply for LECSN2-T Note 1. Between P3 and P4 is connected by default. 2. Always connect between P+ and D terminals. (Factory-wired) 4.
AC (50/60 Hz) 100 V, 200 V, Other voltage (Option) 24 V, Other voltage (Option) 15% to +10% of rated voltage Class B or equivalent (130C) JIS Symbol PA DC Valve type Style N.C.
Alarm output connector (ALARM) D-sub 9 pin (pin) Holding screw: M2.6 Pin No.
D Delta union v v Model Applicable tubing O.D.