Stations: 10, Systems, Port Combinations: AN [Ejector System, ø5/16" (Common PV)], Exhaust: 2 (Individual Exhaust), Wiring: N (No Wiring, No Valve), Bracket: w/o Option, Common Release Pressure Supply: w/o Option, Manifold Individual Supply: L (Manifold Individual Supply Specification)
Driver Type: AN (Pulse Input Type, NPN), I/O Cable Length, m: 3, Driver Mounting: D (DIN Rail Mounting), Table Accuracy: Basic, Size: 10, Max Rotating Torque: J (Basic, LER10: 0.2; LER30: 0.8; LER50: 6.6), Rotation Angle: 3 (External Stopper: 90°)
Stations: 10, Systems, Port Combinations: AN [Ejector System, ø5/16" (Common PV)], Exhaust: Individual Exhaust, Wiring: D-sub Connector, Bracket: w/o Option, Common Release Pressure Supply: D [w/Common Release Pressure Supply (PD) Port], Manifold Individual Supply: w/o Option
For the current/voltage type, 10-bit digital input, and 16-point preset input type ITV1000/2000/3000 series electro-pneumatic regulator, the error contents are indicated in the operation manual.
Refer to the ITV standard type (refreshed product) operation manual. Although this product is a 0 to 5 VDC input signal type, error 1 occurs when an input signal exceeding 5 V is supplied.
The mechanically jointed rodless cylinders leaks air externally due to its seal construction. With a closed center valve, stop positions cannot be held due to the air leakage. To perform intermediate stops, use 2 3-way valves for double-sided pressurization or use a 3-position pressure center valve as a double-sided pressurization control circuit.
https://www.smcpneumatics.com/Part-Builder-Links_ep_2458-1.html?https://smccatalog.partbuilder.smcpneumatics.com/support/faq/en-jp/?ca_id=actuators&fa_id=10099
No, tap water in an open-air tank cannot be used as the circulating fluid for temperature control. The circulating fluid must be circulated in a closed loop.
As a guide, it should be replaced after 6000 to 8000 hours of operation.
For the HRS012/018/024/030 option “T” (high-pressure pump) and the HRS050/060, after 8000 hours, alarm code “AL28” (pump maintenance) will be activated.
We recommend that you check for leaks and replace the mechanical seal at this time. Consider requesting maintenance from a maintenance company. We can recommend
The ZH□-□-X185 vacuum flow can be used to suction machining chips, particles, etc.
By simply supplying compressed air, large flow rate vacuum and blowing greater than the supply volume is possible.
The ZH□-□-X185 vacuum flow features a discharge flow 4 times the supply air volume and suction flow 3 times the supply air volume.
The ZH□-□-X185 catalog can be found
https://www.smcpneumatics.com/Part-Builder-Links_ep_2458-1.html?https://smccatalog.partbuilder.smcpneumatics.com/support/faq/en-jp/?ca_id=vacuum-products&fa_id=10277
It is available via special order. For details, refer to the following.
① When there is no piping rotation stopper, the part numbers are as follows: IRV10-01/02□-X3 and IRV20-02/03/04□-X3.
② When there is a piping rotation stopper, the part numbers are as follows: IRV10-01/02□-X28 and IRV20-02/03/04□-X28.
The IRV10 series catalog can be found
https://www.smcpneumatics.com/Part-Builder-Links_ep_2458-1.html?https://smccatalog.partbuilder.smcpneumatics.com/support/faq/en-jp/?ca_id=vacuum-products&fa_id=10278