ATX-OM-F003E Outer dimensions and descriptions of each part 4Outer dimensions and descriptions of each part 1) Outer dimensions HAW2/7 HAW22 to 110 2VHAW110-30 Flange (mm) Model A B C D E F G H J K L M N P Q R S T U V W Y Z ZA HAW2-04 360 190 83 35 270 35 130 203 159 159 182 209 60 60 94 4.5 10 1/2 1/2 1/2 HAW7-06 570 390 83 35 480 35 130 203 159 159 182 209 60 60 94 4.5 10 3/4 1/2 1/2 HAW22-14 948 575
Plate A Plug (M-3P) (2 pcs.) Plate B (with O-ring) Tighten by hand and give it an additional turn approx. 1/4 rotations with a wrench.
Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight. 2.
2 r w e !0 o !9 !8 i !5 u !7 q !
Note 2) It is suggested to use the silicone grease G-40M made by Shin-Etsu Chemical Co., Ltd. 3) Overhaul 1. Insert the elementA 2E A and the spring washerA 3E A in the direction that the figure shows. 2. Insert the spool valveA 6E A and the guide ringA 9E A together into the body A 1E A. *Be sure to have a performance inspection and an air leakage test after overhaul of the valve.
In particular, for the swivel elbow, the stud may come off. 2) If the fitting is tightened with excessive torque, a large amount of sealant will seep out. Remove the excess sealant. 3) Insufficient tightening may cause seal failure, or loosen the threads. 4) Reuse 1. Normally, fittings with a sealant can be reused 2 to 3 times. 2.
Circuit (Class 2) of maximum 30 Vrms (42.4 V peak) or less, with UL1310 Class 2 power supply unit or UL1585 Class 2 transformer. The product is a UL approved product only if it has a mark on the body. Use the specified voltage. Otherwise failure or malfunction can result. Insufficient supply voltage may not drive a load due to a voltage drop inside the product.
200 S AS 01 X785 Pilot port Port size Body size Thread type Seal method 2 1/8, 1/4 3 3/8 4 1/2 Nil R, Rc G G Nil Without sealant (for G) S With sealant (for R) Cylinder side 01 1/8 02 1/4 03 3/8 04 1/2 * R thread type: With sealant G thread type: Without sealant Valve side Cylinder side 04 F 10 S AS4201 X785 Pilot port Thread type Seal method Nil R, Rc G G Nil Without sealant (for G) S With
This may cause leakage or disconnection of the tubing. 7 2. Specific Product Precautions (4) (1) Fittings with sealant: R 1) First, tighten the fitting by hand, then use a wrench appropriate for the hexagon flats of the body to tighten it a further two or three turns. For a tightening torque guide, see the table below.
A B (mm) Model A 21h9 28h9 35h9 35h9 B 2 2 2 2 Weight (g) 805 1,097 1,943 2,825 MHT2-32DZ-X5070 MHT2-40DZ-X5070 MHT2-50DZ-X5070 MHT2-63DZ-X5070 0 0.052 0 0.052 0 0.062 0 0.062 653 A
(In order of (1), (2) in drawing on the right) (8) If O-ring is swollen, replace it with a new O-ring. Bolt Nut (2) Hex.
above. (2) If your operating conditions are different from these basic conditions, apply a correction factor.
If a sealant tape is used, leave 1.5 to 2 threads exposed. 2 Wrap this way. Leave 2 threads. Sealant tape Handling Caution (1) Do not apply force when transferring, mounting and dropping the regulator with a pressure gauge.
IR-OM00015 PRODUCT NAME Precision Regulator MODEL / Series / Product Number IR300(0, 1, 2)-A IR301(0, 1, 2)-A IR302(0, 1, 2)-A Contents Safety Instructions 2 to 6 1. Application 7 2. Specifications 7 3. Construction and Operation Principles 8 4. How to order 9 5. Bracket, gauge and switch assembly (optional) 10 6. Panel mounting 11 7. Troubleshooting 12 8.
Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight. 2.
Ta 10 STa(S 10) = & I Ta (Nm) I: & 2 = & (rad/s2) 2 t 5.2 5.3 22 5.4 P A F 1 1 = (1) P A F 2 2 = (2) 2 1 D 4 A = (3) ) d D ( 4 A 2 2 2 = (4) F=[N] F=[N] = A=[mm] A=[mm] D=[mm] d=[mm] P=[MPa] 5.6 () 5.7 () 5.5 23 6. 6. 6. 6. ,, , ,, 6-1. 6.1 (m) DC AC 0.5 3 5 (L) (Z) (N) 3 (NPN) F7NV F79 3 (PNP) 5V,12V F7PV F7P IC F7BV J79 2 12V J79C 24V 3 (NPN) F7NWV F79W PLC 3 (PNP) 5V,
If a sealant tape is used, leave 1.5 to 2 threads exposed. 2 Wrap this way. Leave 2 threads. Sealant tape Handling Caution (1) Do not apply force when transferring, mounting and dropping the regulator with a pressure gauge.
Range Sets lower limit of temp. range which causes a warning to occur. 1) Strip the sheath from both ends of the cable. 2) Disassemble the power supply connector.
Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight. 2.
None, Odd, 6 Parity Bit Even None 2 Control Operation 0,1,2,3,4,5 1 Operation of the pump with a large amount of air left in the piping for When cleaning the panel use a vacuum cleaner to remove the dust. Do 7 Data Length Sets data length for communication. 7Bits, 8Bits 8 prolonged period may damage the pump.