2 . ; A A LEFS40 : = B > > 8 @ A-A . ; 2 A A No.
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
failsafe system is a system that remains in the safe state or immediately enters a safe state when specific failures occur. i-Parameter Individual safety parameters of a module OSSD An Output Signal Switching Device is a safety related output of a sensor that are self-checked.
3 Set of above @3, @4, @5, @6, @7 and @8 16 20 25 32 40 50 63 80 100 MGP16-A-PS MGP20-A-PS MGP25-A-PS MGP32-A-PS MGP40-A-PS MGP50-A-PS MGP63-A-PS MGP80-A-PS MGP100-A-PS Hex. socket head tapered plug Slide bearing Felt Resin Ball bushing Set of above @3, @4, @5, @6, @7 and @8 !4 !5 !6 !
With end lock Working principle A + A A Series CXS 6, 10, 15, 20, 25, 32 Piston seal A A A CX2 R H R H CXW 1. When the piston is retracting, air is exhausted through both A and A until piston seal H passes air passage A. 2. After piston seal H has passed air passage A, air is exhausted only through A.
A 2 A Power supply (Output) 24 VDC +10/-5%, 24 VDC +10/-5%, 8 A DC24 V +10/-5%, 4 A 2 A Enclosure IP67 (With manifold assembled) 1 Environment Operating temperature range -10 to 50 oC Storage temperature range -20 to 60 oC Operating humidity range 35 to 85%R.H.
A12 Symbol, A13 Symbol A14 ::l C. ~ ,DA c Rball 1 \ B ~l , I ~ I H l i Symbot, A16 Symbol,A15 Symbol' A17 Symbol A1S Symbol A 19 .. ~ ~i >If? I ~ A H / ~ M 30' ! " A I H 30' MM .. Symbol A23 -j -j Symbok A21 Symbok A20 Symbol' A22 Symbol, A24 30' I Q " m "~ M , I 30' ~i m " o 0 " '-/! T T A A L : AL : A H , H H H Symbot, A26 Symbok A25 Symbol' A27 ~!'~~~ _ '_ 7) M A =~O=D=A=3 ~!
Use a speed controller to adjust the cylinder drive speed, gradually increasing from a low speed to the desired speed setting. Provide an intermediate support for a cylinder with a long stroke.
Therefore, internal parts of a cylinder other than rod seal are not replaceable. 2. Use caution to the popping of a retaining ring. When replacing rod seals and removing and mounting a retaining ring, use a proper tool (Retaining ring plier: Tool for installing a type C retaining ring).
Refer to the Specific Product Precautions. 28.5 32 Z ZZ G (NN 1) x H 8.5 18.5 8.5 18.5 H B A 4.2 8.5 9 9 20 1 4H9 depth 3.5 +0.030 0 5 B A NN x M5 x 0.8 thread depth 10 4H9 depth 3.5 +0.030 0 HA GA Section AA Section BB (mm) HA 40 40 40 25 36 72 76 Model F 35 35 35 50 35 55 65 N 4 4 4 4 6 6 6 G 15 15 15 17 15 25 35 H 40 40 40 25 36 36 38 NN 2 2 2 3 3 4 5 GA 15 15 15 42 51 61 111 I 10 10
+ A = 100 y, z + A 100 10 y, z + A = 200 y, z + A = 200 y, z + A = 300 y, z + A = 300 1 1 0 200 400 600 800 1000 1200 0 100 200 300 400 500 600 700 800 Stroke [mm] Stroke [mm] [Graph 6] Allowable load mass by stroke 32 [Graph 5] Allowable load mass by stroke 25 100 100 y, z + A = 0 y, z + A = 0 y, z + A = 50 y, z + A = 50 10 Load mass [kg] Load mass [kg] 10 y, z + A = 100 y, z + A = 100
A slit panel and a panel without slit are used in combination. Refer to the operation manual for details.
Use the table as a guideline for mounting.
watch maker's screwdriver with a grip diameter of 5 to 6mm.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
Note that sometimes a load is applied to the buffer by a piping tube (pulling or pressing, etc. in a lateral direction). 5. Do not apply an impact or large force to a pad when adsorbing a workpiece. This will cause deformation, cracking and wear of the pad to be accelerated. The stiffening ribs, etc. should touch lightly, while staying within the pad skirts deformation range.
watch maker's screwdriver with a grip diameter of 5 to 6mm.
In the graph, find where the lines representing a load mass of 10 kg and a stroke of 300 mm intersect. A 50 bore size is selected.