D-F6N/D-F6P/D-F6B Do not use in direct sunlight. 8. Do not mount the product in locations where it is exposed to radiant heat. 9. Take appropriate measures against the lightning surge on the equipment side as the auto switches do not have any lightning surge resistance specified in the CE marking. Caution 1.
Transporting using casters 1) This product is heavy and should be moved by at least two persons. 2) Do not grip the piping port on the right side or the handles of the panel. 3) When transporting using a forklift, be sure not to let it hit the casters or adjusters, and drive the fork all the way through until it comes out the other side. 4) Do not get across steps with casters. 2.
The sending side calculates the data every 2 bytes (16 bits). The receiving side calculates CRC based on the received message, and compares the calculation result with the received CRC. The received message is deleted if the calculation result and received CRC do not match.
Do not collide the pallet while the lever is standing erect. For the lever with built-in shock absorber, do not collide the next pallet while the lever is standing erect. Otherwise, all energy will be applied to the cylinder body. 2.
of read outputs: 16 bits (10h) 12 1 (Number of bits) 13 0 Calculated 14 value Checksum(LRC) 15 Calculated value 16 End code CR 17 LF Note 1: The maximum value is 456 bits.
Do not twist the valve seal 1. Use dust-free gloves. 16 XL-OMS0001-B Step 5 Remount of external seal Step 6 Reassembly of bonnet assembly (No.1) Valve seal 1 External seal Mounting part of the external seal Bellows holder Bonnet assembly Body Wipe off any dust from the surfaces of the valve seal 1 and the bellows holder.
Hold/Release success: default output DO[101] Hold/Release failure: default output DO[102] * Digital output port can be selected within DO[101] to DO[112] * you select the same digital output port for different status signals, a warning message will be displayed. 2. Test run The manual operation of the magnet gripper unit can be checked.
Do not use in these conditions. (Refer to specifications.) Consult SMC if a fluid other than compressed air is used. 2.
not occur on the product of the cooling method -W. 2: These alarms do not occur on the product of the power specification '-20'.
Do not use pressure sensors with corrosive and/or flammable gases or liquids. 4. Connection of sensor connector Cut the sensor cable as illustrated to the right. Referring to the table below, insert each lead wire of the cable at the position marked with a number corresponding to 1.
Failure to do so may cause equipment failure or malfunction. 9. Mount the Fieldbus system in a location where there is no excessive vibration or shock. Failure to do so may cause equipment failure or malfunction. 10. Do not use in places where there are cyclic temperature changes.
Do not drop or bump. Do not drop, bump or apply excessive impacts (300m/s or more for reed switches and 1000m/s or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Do not mount the product in locations where it is exposed to radiant heat. 5. Do not use in dusty locations or where water, oil, etc., splash on the equipment. 6.
Do not use in locations where static electric charges will be a problem. Consult SMC regarding use in this kind of environment. 6. Do not use in locations where spatter occurs. There is a danger of spatter causing a fire.
Do not use in locations where static electric charges will be a problem. Consult SMC regarding use in this kind of environment. 6. Do not use in locations where spatter occurs. There is a danger of spatter causing a fire.
For type W, DC voltage is only 5 16" One-touch fitting for N9 5 5 16" One-touch fitting for N9 One-touch fitting for One-touch fitting for One-touch fitting for available.
through until it comes out the other side. 4) Do not get across steps with casters.
I" = 2. 4. 6. 8.. ) (n = 4.8, 12. 16") (n = 4, 8, 12. 16 .. ) (n = 4, 8, '2, 16 ..) With 2 pes. (DiUerent surfaCfls 115 20 120 ' 25 Same surface), With 1 pc (n '" 2. 4. 6, 8.. ~_-L_("":.:=,, 4 "2 ' :0 .. ,1 _ (" ,,.-,,8,-.' ' :0.. ) ".-,,. ' "2,,.-,-"." ) ,,.-,,8,-.' ,,.,,6.")
Do not operate with anything other than compressed air. The cleaning equipment has been designed to be used only with compressed air. To use fluids instead of compressed air, please contact SMC beforehand. 2. Do not use compressed air that contains chemicals, organic solvents, salt, or corrosive gases.
6Element mounting bracket 16-1 16-2 16-3 472 Series FGB Replacement Procedure of Element 2 4. Method for Removal of Element Assembly 2. Overhaul 2-1. If the differential pressure rises due to clogging and reaches the threshold for element replacement (0.1 MPa), replace the element with the new one. 2-2.