IDX-OM-O004E Specification for Option L 10 . 1 Safety instructions . 10 1 10 . 2 Specifications . 10 1 10 . 3 Installation of heavy duty auto drain . 10 2 10 . 4 Maintenance . 10 2 Chapter 11 Specification for Option M 11 . 1 Safety instructions . 11 1 11 . 2 Specifications . 11 1 11 . 3 Installation of motor type auto drain . 11 2 11 . 4 Electric wiring diagram . 11 2 Chapter 12 Specification for Option
MU-D02 MU-D03 MU-D04 MU-D05 +0.058 0 +0.058 0 +0.058 0 +0.058 0 +0.058 0 +0.058 0 +0.058 0 +0.070 0 8 10 10 14 8 10 10 14 Applicable pin no. CD-MU02 CD-MU03 CD-MU04 CD-MU05 DZ 8 10 10 14 CZ 8 10 10 14 DY 9 11 13 16 CX 9 11 13 16 DX 18 22 26 32 CT 9.5 11 14 17 DT 9.5 11 14 17 CR 5.3 6.4 8.4 10.5 DR 5.3 6.4 8.4 10.5 CL 26 42 54 64 DL 26 42 54 64 Part no.
Do not ground to water pipe, gas tube or lightening rod line. 7. Do not connect too many wires to the same outlet, which could results in heat generation and fire. 8. Do not retrofit the wiring of the dryer and the power supply line. 9.
kPa 25 kPa 50 kPa Electrical Power supply voltage 12 to 24 VDC (10%), and power supply ripple (p-p) 10% at max. spec.
Do not modify the internal electrical wiring of the product. 10.2 Earth leakage breaker specification Models Item IDFC60-23-R IDFC70-23-R IDFC80-23-R IDFC90-23-R Rated current (A) 10 15 20 30 Sensitivity current (mA) 30 IDFC60/70/80/90 Series 10.1 Safety instructions for use 10-1 IDX-OM-U010 Chapter 10 Option R 10.3 Connection of power supply Connect the power cable according to the procedure
Bolt used Max. tightening torque Nm(kgf/cm) Max. screw-in depth l (mm) Type MXS 6 MXS 8 MXS12 MXS16 MXS20 MXS25 0.9{9.2} 0.9{9.2} 2.1{21.4} 4.4{44.9} 4.4{44.9} 7.4{75.5} 4 5 5.5 6 10 13 M3 x 0.5 M3 x 0.5 M4 x 0.7 M5 x 0.8 M5 x 0.8 M6 x 1 Bottom screw Do not rotate. Piston rod Precautions for Adjuster Option Do not damage.
Do not bring items, which are sensitive to or affected by magnetism close to the product. (4) Do not operate the Card Motor continuously with maximum thrust force.
Clevis (1) RCS-015 RCS-02 RCS-03 RCS-04 RCS-05 RCS-08 RCS-10 Pin (1) PS-015 PS-02 PS-03 PS-03 PS-05 PS-08 PS-10 Clevis (1) RCD-015 RCD-02 RCD-03 RCD-04 RCD-05 RCD-08 RCD-10 Pin (1) PS-015 PS-02 PS-03 PS-03 PS-05 PS-08 PS-10 Snap rings (2) PC-01 PC-02 PC-03 PC-03 PC-05 PC-08 PC-10 Snap rings (2) PC-01 PC-02 PC-03 PC-03 PC-05 PC-08 PC-10 056(9/16") 075(3/4") 106(1 1/16") 150(1 1/2") 200(2")
Do not short-circuit the load. Although error is displayed when the Pressure switch load is short circuit, generated excess current lead to cause the damage of the Pressure switch. Do not press the setting buttons with a sharp pointed object. It may damage the setting buttons. If using the product to detect very small pressure rates, warm up the product for 10 to 15 minutes first.
5.5 M3 x 0.5 M4 x 0.7 M5 x 0.8 M6 x 1.0 32 38 47 52 5 6 8 10 3.5 3.5 4.5 5 15.5 20 25.5 28 3.5 3.5 5.4 5.4 M4 x 0.7 M4 x 0.7 M6 x 1.0 M6 x 1.0 6.5 6.5 9 9 7.5 7.5 9 11 7 7 10 10 4 4 7 7 0.5 0.5 1 1 Note 1) Threaded through hole is used for the standard of 20 with 5 to 10 mm strokes and 25 with a 5 mm stroke.
15 30 35 10 18 21 35 35 35 10 22 35 35 1.2 1.9 2.1 2.1 1.8 2.1 2.1 2.1 0.5 0.8 1.8 2.1 0.5 1.0 1.2 1.9 1.9 2.1 0.5 1.3 1.8 2.1 0.4 0.4 0.5 0.5 0.5 0.5 0.5 0.5 0.4 0.4 0.5 0.5 0.4 0.4 0.4 0.4 0.4 0.5 0.4 0.5 0.5 0.5 R1/8 R1/4 R3/8 R1/2 Rc1/8 Rc1/4 Rc3/8 Rc1/2 6 (1/4") 8 (1/4") 10 (3/8") 12 (1/2") 5/8 6/9 6.5/10 8/12 8.5/12.5 11/16 6 8 10 12 4.2 7.0 7.0 7.0 6.0 7.0 7.0 7.0 2.0 3.0 6.0 7.0
1 5 5.5 7.5 1 [3.5] 6 5.5 9 10 1 5 5.5 7.5 17 19 22.5 24.5 10 9.5 13 14 5 9 9.5 11.5 5 4.5 0.5 1.5 10 9.5 13 14 5 9 9.5 11.5 10 9.5 13 14 5 9 9.5 11.5 0.5 [3] 3.5 [1] 5.5 [3] DDouble Acting, Double Rod 1.5 2 6 7 19.5 21.5 25 27 2.5 3 2 4 12 16 20 25 5.5 5 10 12 3.5 [6] 3 [5.5] 8 [10.5] 10 [12.5] 1.5 2 6 7 5.5 5 10 12 17 19 22.5 24.5 5.5 6 10 11 9.5 9 14 16 0.5 1 4 6 5.5 6 10 11 9.5 9 14 16
Do not press the setting buttons with a sharp pointed object. It may damage the setting buttons. If using the product to detect very small pressure rates, warm up the product for 10 to 15 minutes first. There will be a drift on the display of approximate 1% immediately after the power supply is turned on, within 10 minutes. Perform settings suitable for the operating conditions.
ISE79S Applicable fluid Liquids and gases do not corrode the parts in contact with fluid Rated pressure range 0 to 50.0 MPa Pressure spec. Display/set pressure range -2.5 to 52.5 MPa Display/min. set unit 0.1 MPa Proof pressure 75 MPa Power supply Used as switch output device 12 to 24 VDC 10% with 10% voltage ripple or less voltage Electric spec.
Do not apply heat cycle.) Operating fluid temperature 0 to 100C (Not be frozen. Do not apply heat cycle.)
Do not press the setting buttons with a sharp pointed object. It may damage the setting buttons. If using the product to detect very small pressure rates, warm up the product for 10 to 15 minutes first. There will be a drift on the display of approximate 1% immediately after the power supply is turned on, within 10 minutes. Perform settings suitable for the operating conditions.
) 24VDC (10%) 24VDC (10%) 100 to 240VAC (10%) 100 to 240VAC (10%) 100 to 240VAC (10%) 24VDC (10%) 100 to 240VAC (10%) Power consumption 20VA or less 10W or less 20VA or less 10W or less 20VA or less 10W or less 10W or less 20VA or less Between case and AC line: 1500VAC for 1 min.
Unit 1 -10..10 V -5..5 V -20..20 mA 0..10 V Selects the analogue input range. -10..10 V Channel 2 Analogue input range Sets the analogue input device range. 0..5 V 1..5 V 0..20 mA 4..20 mA Offset binary Offset binary. Sets analogue data type which is output to PLC. 2s complement 2s complement.
2 (Different surfaces) 10 n 10 + 30 (n 2) D-A9l 2 (Same surface) 50 1, 2 (Different surfaces) 10 n 10 + 40 (n 2) D-A9lV 2 (Same surface) 40 1, 2 (Different surfaces) 10 n 10 + 30 (n 2) * n = 3, 4, 5 * The D-M9lV/M9lWV/M9lAV/A9lV are mountable on 32 to 63.
Do not press the setting buttons with a sharp pointed object. This may damage the setting buttons. Supply the power when there is no flow. If using the product to detect very small flow rates, warm up the product for 10 to 15 minutes first. There will be a drift on the display or the analogue output of approximate 2 to 3% immediately after the power supply is turn on, within 10 minutes.