Shock Absorbers and Rate Controls

l llunbcr llodel (Rell B C .05 t) t t G Eolt Slts w?isl'r t-t 2 300 0lhy4 1 8?.6 6.4 ,7 f9.9 ( o E SC!

Series 10-V100 Rubber seal 3 port direct operated solenoid valve

Note 2) For 10-V124(A) How to Order Valve Manifold Assembly Ordering example Stations 5 4 3 2 1 Valve (N.C.) 10-V114-5GZ 2 1 3 2 Blanking plate assembly V100-77-1A Manifold base (5 stations) 10-VV100-S41-05-M5 10-VV100-S41-05-M51 set (S41 type 5 station manifold part no.)

AC

Caution qInstallation location Do not install this product in an area that is exposed to water or direct sunlight. Do not install it in an area that is exposed to vibrations. If it must be used in such an area due to unavoidable circumstances, contact SMC beforehand.

3 Port Solenoid Valve Metal Seal/Rubber Seal, Base Mounted Series VQZ100/200/300 21

AXT100-20-2-05 AXT100-20-2-06 AXT100-20-2-01 AXT100-20-2-02 AXT100-20-2-03 AXT100-20-2-04 13.8 24 VDC 12 VDC 100 VAC 200 VAC 110 VAC 220 VAC 24V 12V 100V 200V 110V 220V 1. It is able to change the cylinder port between side ported and top ported.

3 Port Solenoid Valve Metal Seal/Rubber Seal, Body Ported Series VQZ100/200/300 1

Caution Do not apply excessive torque when turning the locking type manual override.

3 Port Solenoid Valve Metal Seal Series VZ200 1

Type 20) 3 110 VAC, 50/60 Hz Nil Push type (Safety style) G H L LN L plug connector With lead wire 600 mm lead wire 300 mm lead wire 4 220 VAC, 50/60 Hz Grommet B Locking type (Tool required) 2 Body side exhaust (Type 30, 50) 5 24 VDC 6 12 VDC C Locking type (Manual) Without lead wire Without connector With lead wire Without lead wire Without connector MO With connector D Without connector DO

VZS

DXT170-176-2-01 DXT170-176-2-02 100 VAC 200 VAC 100V 200V DXT170-176-2-03 220V 110V 110 VAC DXT170-176-2-04 220 VAC DXT170-176-2-07 DXT170-176-3-51 DXT170-176-3-06 DXT170-176-3-05 DXT170-176-3-53 240 VAC 240V 6VD 12VD 24VD 48VD 6 VDC 12 VDC 24 VDC 48 VDC Circuit with Indicator Light AC Circuit diagram DC Circuit diagram D: Protective diode LED: Emitting diode R: Resister NL: Neon bulb R:

5 Port Solenoid Valve Metal Seal/Rubber Seal Body Ported

The latching solenoid option (with self holding mechanism) functions in the same manner as a 2 position double solenoid but uses only one solenoid to do the job.

VEX1

Hz) 1 2 3 Symbol Port size Thread type Symbol Sub-plate A B 1/8 1/4 Nil Rc G NPT NPTF F N T 4 5 6 7 Base gasket VEX1 11 2 9 Other Option Body size Port size Electrical entry (Only with solenoid) Port size Body size Electrical entry Port 1(P), 2(A) 3(R) 01 1 02 1 8 1 8 G Grommet (Lead wire length 300 mm) 1 4 1 4 H Grommet (Lead wire length 600 mm) 02 3 03 1 4 1 4 D DIN terminal 3 8 3 8 DO

4

Non-locking push type Unrestricted 150/50 m/s2 Make sure that dust and/or other foreign materials do not enter the valve from the unused port (e.g. exhaust port).

Square Tube Type Air Cylinder Series MB1

DO Without air cushion (mm) B Bore size (mm) No.

5 Port Solenoid Valve/Body Ported, Cassette Type Manifold, Series SY3000/5000/7000

D and DO type DC specifications are 24VDC or 12VDC only. D and DO type are for SY5000/7000 only.

Fluoropolymer Piping Equipment

Do not use in locations having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. In locations near heat sources, block off radiated heat. 1. Cut the end of the tubing at a right angle and pass it through the fitting nut. After placing the tubing in the holder, push it onto the insert bushing until it stops and clamp it with the knob.

7

However, do no rotate the cushion valve exceeding two turns, and do not rotate the speed controller valve exceeding four and half turns (40: maximum two turns). If 0.6 Nm or more of torque is applied, the valve may become loose and may jump out depending on the amount of air pressure. Cushion Adjustment The air cushion is built in on the head end for the CK1 series.

Compact and Lightweight

Do not excessively expand or bend the bracket as it may break. The appropriate tightening torque for the standard bracket is shown below.

Compact Vacuum Ejector Series ZA

Do not use for other purposes. Solenoid valve combination symbol Combination no.

Clamp Cylinder Series CK1

Do not leave out the component parts when the piping port location is changed. Even if one of the component parts is not replaced, malfunction may occur, resulting in dangerous operation. 2. To prevent air leakage, re-wind the pipe tape and fit into the changed location when the piping port location is changed.

Booster Regulator Series VBA1110 to 4200 1

Installation location Do not install this product in an area that is exposed to water or direct sunlight. Do not install in locations influenced by vibrations. If it must be used in such an area due to unavoidable circumstances, please contact SMC beforehand. 14-9-4 5 Booster Regulator Series VBA1110 to 4200 4.

VCA

For air VV2CA3-05 VCA35-5G-4-03 1 set Manifold part no. 5 sets Valve part no. (Stations 1 to 5) IN port direction Side Front Nil A Series is the symbol for assembly. Add an in front of the part numbers for solenoid valves, etc., to be mounted. 3 4 Class 3 Class 4 Enter together in order, countingfrom station 1 on the D side.

Vacuum Ejector with Solid State Timer

Do not allow repeated bending or stretching forces to be applied to lead wires. Wiring arrangements in which repeated bending stress or stretching force is applied to the lead wires can cause broken wires. 1. Do not drop or bump. Do not drop, bump or apply excessive impact (1,000m/s) when handling.