Fieldbus System valve (A) (A) 4 (B) 2 (A) 4 (B) 2 Note) A 1 5 (R1) 3 (R2) 1 (P) 3 (R2) 5 (R1) 1 (P) N.C.
If there is a risk of contact, provide safety measures such as a cover or a system that uses sensors that will activate an emergency stop before contact is made. 2. Use a balance circuit in which lurching of the piston is taken into consideration.
From a point indicating 500 mm/s on the axis of abscissas, extend a line upward and find a point where it intersects with a line for the 63 mm bore size. Extend a line from the intersection to the left and find a load mass 80 kg.
C0.5 file chamfer AL B MM R sphere TP R sphere DC 30 H W1 T H H H Symbol: A12 Symbol: A13 Symbol: A14 Symbol: A15 30 C 30 DA DA C0.5 R sphere DA DA C AL MM 30 A H T W1 A H C A H H Symbol: A16 Symbol: A17 Symbol: A18 Symbol: A19 MM 30 MM 30 DA MM 30 AL MM 30 H A H A A C H A H Symbol: A20 Symbol: A21 Symbol: A22 Symbol: A23 DA 30 30 DA L RD 30 MM 30 MM MM DB DB T T C B A H A A A L K H W H H
Single solenoid type A side solenoid Black: A Red: COM Double, 3 position type A side solenoid Black: A Red: COM Valve B side solenoid White: B Red: COM Lead wire color Lead Wire Color Single solenoid type A side solenoid Black: A Red: COM Double, 3 position type A side solenoid Black: A Red: COM Valve (1) B side solenoid White: B Red: COM Lead wire color Lead wire length: 0.6 m 3-7-4 5 Series
How to Replace One-touch Fittings How to Replace Silencers Warning A single body ported valve has a built-in silencer. A dirty and clogged silencer may reduce cylinder speed or cause a malfunction. Replace the silencer periodically. The cylinder port fittings are a cassette for easy replacement.
S) SMC C A B D SMC B A SMC (Max. T) U Z M N LVQ40, LVQ60 C B A D (Max.
A B C A B A B A B A B Application Same tubing size 1 2 1 2 1 2 3 1 2 1 2 1 2 Refer to the applicable tubing table.
A B C A B A B A B A B 15A 20A 25A Note 1) For each piping diameter for each body size, the second and later numbers or symbols indicate reducing.
ML2B Usable without a stopper nut The strong body can be positioned directly.
center 3 position exhaust center 3 position closed center 3 position pressure center (1) 3 position exhaust center 3 position closed center (A) 4 (B) 2 (A) 4 (B) 2 (A) 4 (B) 2 (A) 4 (B) 2 (A) 4 (B) 2 (A) 4 (B) 2 5 (R1) 1 (P) 3 (R2) 5 (R1) 1 (P) 3 (R2) 5 (R1) 1 (P) 3 (R2) 5 (R1) 1 (P) 3 (R2) 5 (R1) 1 (P) 3 (R2) 5 (R1) 1 (P) 3 (R2) Note 1) Except VQZ1000 and metal seal.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
Note that sometimes a load is applied to the buffer by a piping tube (pulling or pressing, etc. in a lateral direction). 5. Do not apply an impact or large force to a pad when adsorbing a workpiece. This will cause deformation, cracking and wear of the pad to be accelerated. The stiffening ribs, etc. should touch lightly, while staying within the pad skirts deformation range.
Note 2) Contact P/A if a stroke greater than the maximum stroke is desired.
PB B A B A B A N.C. N.O. Double acting Double acting With flow rate adjustment PA PA N.C. B A PB B A Double acting N.C. Double acting With by-pass PA PA N.C. PB B A B A Double acting N.C. Double acting With flow rate adjustment & by-pass PA PA N.C. PB B A B A Double acting N.C.
After tightening by hand, tighten an additional 1/4 rotation for M3 and 1/6 rotation for M5 with a tool. However, when using a miniature fitting, tighten an additional 1/4 rotation with a tool after tightening by hand. Also, when there are 2 gaskets such as in case of a universal elbow or universal tee, tighten an additional 1/2 rotation.
Note that sometimes a load is applied to the buffer by a piping tube (pulling or pressing, etc. in a lateral direction). 5. Do not apply an impact or large force to a pad when adsorbing a workpiece. This will cause deformation, cracking and wear of the pad to be accelerated. The stiffening ribs, etc. should touch lightly, while staying within the pad skirts deformation range.
A B B Dimensions A Dimensions A (mm) (mm) B C D F Y B C D F Model Model ZPT10F-B5-A8 ZPT20F-B5-A10 10 12 10 12.5 37.5 20 22 1.5 12.5 15.5 48.5 ZPT13F-B5-A8 ZPT25F-B5-A10 13 15 25 28 10.5 13 38 ZPT16F-B5-A8 ZPT32F-B5-A10 2 13 16 49 16 18 32 35 ZPT 40/50 F-B5-A14 (Without Buffer/Male Thread) M14 x 1 Width across flats 19 M5 x 0.8 5 5 20 D 5 F Width across flats 21 C Y 2.5 A B Dimensions A (
A One-touch fitting for 12 is attached to each port.