SMC Corporation of America
Elite Part Number Search
Search Results "CQ2B16-T-PS"

Piping specifications R06 R07 6 reducer 1/4" reducer L 3 m Lead wire length Switch Specifications PS1000/PS1100 PS1200 psi (MPa) 58 (0.4) 0 psi (kPa) 29 (0.2) 7.25 (50) Set pressure Set pressure 0 14.5 (0.1) 14.5 (100) t t The switch turns ON when the set pressure is reached or exceeded. The switch turns ON when at the set pressure or below.

T VMG Applicable tubing Connection thread (With seal) Male Elbow: KXL (High speed) H (width across flats) Applicable tubing O.D.

Not applicable for types: Double rod (W), Trunnion (T), XC8, XC9, XC10, XC11, Over sized rod (XB5) with front mounts.

V Voltage dV dt = Voltage ratio Voltage rise % on zero-cross point dV t Time dt 3.3 Installation HRL Series 3-10 HRX-OM-W060 Chapter 3 Transport and Setting Up Power supply specifications, power supply cable and earth leakage breaker Prepare the power supply shown in the following table.

IS3000-02 IS3100 IS3010-02 IS3110 Standard 5 VDC 160 mA Z I SE3 Micro load 5 VDC 1 mA PS Easy electrical wiring Wide space for wiring. Fixed wiring possible with G 1/2 connector.

Description q w e r t y u i o !0 !1 !2 !3 !4 Material Rod cover Head cover Cylinder tube Piston rod Piston Cushion ring Rod bushing Cushion valve Tie-rod Tie-rod nut Retaining ring Rod seal retainer Cushion seal Rod seal Piston seal Cushion valve seal Cylinder tube gasket Piston gasket Wear ring Rod jam nut Components included in a seal kit.

PB Construction Component Parts q e Description Solenoid coil Body Fixed armature Armature Return spring Poppet Diaphragm assembly Material No. q w e r t y u r Resin Stainless steel Stainless steel Stainless steel NBR HNBR, Resin w t y u 17-2-83 Series VQ20/30 Dimensions: Series VQ20 In-line Type: Grommet (G) VQ21A1-GBracket mounting holes Mounting holes 2-3.2 through 2-3.2 through Light

: 32C, w Circulating uid: Tap water, e Circulating uid ow rate: Rated ow, r Power supply: 200 VAC 4 q Ambient temperature: 32C, w Circulating uid: Tap water, e Circulating uid temperature: CH1 20C/CH2 25C, r Load: Same as the cooling capacity, t Circulating uid ow rate: Rated ow, y Power supply: 200 VAC, u Piping length: Shortest 5 With the pressure control mode by inverter.

Simple Pressure Vessels Directive This directive is applied to welded vessels whose maximum operating pressure (PS) and volume of vessel (V) exceed 50 bar/L. Such vessels require EC type examination and then CE marking. 15-18-6 SMC Product Conforming to International Standards national Standards you to comply with EC directives and CSA/UL standards.

Nylon Tubing Series T/TIA For general pneumatic tubing, Nylon tubing Model/Specifications 20 m roll 100 m roll (T1613 is reel.) Tubing size Metric size (Series T) Inch size (Series TIA) Burst Pressure Characteristics Curve and Operating Pressure TIA01 T0425 T0403 T0604 T0645 T0806 T1075 T1209 T1613 TIA05 TIA07 TIA11 TIA13 Model Tubing O.D.

Simple Pressure Vessels Directive This directive is applied to welded vessels whose maximum operating pressure (PS) and volume of vessel (V) exceed 50 bar/L. Such vessels require EC type examination and then CE marking. 14-21-6 SMC Product Conforming to International Standards national Standards you to comply with EC directives and CSA/UL standards.

Simple Pressure Vessels Directive This directive is applied to welded vessels whose maximum operating pressure (PS) and volume of vessel (V) exceed 50 bar/L. Such vessels require EC type examination and then CE marking. 15-18-6 SMC Product Conforming to International Standards national Standards you to comply with EC directives and CSA/UL standards.

Description Body Note Baking finish Material q Aluminum alloy w w Aluminum alloy Baking finish Housing e Aluminum alloy Baking finish Drain guard y r Foam rubber Float IN t Stainless steel + Rubber Pilot valve y Resin Lever u Brass Flushing button t i Orifice r o Rubber Diaphragm Replacement Parts 10-1 e No. Description Part no. ADH-D400 Note 10-2 !

Description q w e r t y u i o !0 !1 !2 !3 !4 Material Rod cover Head cover Cylinder tube Piston rod Piston Cushion ring Rod bushing Cushion valve Tie-rod Tie-rod nut Retaining ring Rod seal retainer Cushion seal Rod seal Piston seal Cushion valve seal Cylinder tube gasket Piston gasket Wear ring Rod jam nut Components included in a seal kit.

Ex. 2) When using contact b only IN PS LAMP LIGHTS WHEN PRESSURE RISES. N.C. C. CR Caution ISA No. Component Parts 1. In the case of using a switch with indicator light, wire the indicator light per the following: 2. Please put the enclosed seal of LAMP LIGHTS WHEN PRESSURE RISES. or LAMP GOES OUT WHEN PRESSURE RISES. on the equipment where it is easy to see.

Before any machinery or equipment is removed, forst ensure that the appropriate measures are in place to prevent the fall or erratic movement of driven objects and eqipment, ten cut off t electric power and reduce the pressure in thesystem to zero. Only then should you proceed with the removal of any machinery and equpment.

Simple Pressure Vessels Directive This directive is applied to welded vessels whose maximum operating pressure (PS) and volume of vessel (V) exceed 50 bar/L. Such vessels require EC type examination and then CE marking. 15-18-6 SMC Product Conforming to International Standards national Standards you to comply with EC directives and CSA/UL standards.

Description Material PBT Brass Brass Note) Handle Needle Lock nut Needle guide Washer O-ring Silencer Silencer cover Body B Gasket q w e r t y u i o !

Simple Pressure Vessels Directive This directive is applied to welded vessels whose maximum operating pressure (PS) and volume of vessel (V) exceed 50 bar/L. Such vessels require EC type examination and then CE marking. 15-18-6 SMC Product Conforming to International Standards national Standards you to comply with EC directives and CSA/UL standards.