SMC CORPORATION OF JAPAN Press the + button to add a block. 2 ) Step 2: Choices will appear on the right side of the screen that include System Outputs (if available), existing Function Blocks that have free input pins, and the option to add a new function block (AddFB, see section 4.4).
Removal of the cup. (1) Remove the suction cup with adapter from plate B using a spanner. (2) Loosen the bolt (M4 x 8), then remove plate B from plate A. Be careful not to lose the O-ring. (3) Loosen the bolt for sealing (M6X8), then remove the cup from plate A. 2.
Unit: Nm Recommended Torque Connection thread 1/8 1/4 3/8 1/2 3/4 1 1 1/2 2 Torque 7 to 9 12 to 14 22 to 24 28 to 30 28 to 30 36 to 38 48 to 50 48 to 50 * After tightening by hand, use a tightening tool to tighten an additional 1/6 turn. 2. Select according to the maximum flow rate of the system. 2.
TQ1230001-OM101-D 6.3 Change to 2 cups 1. Removal of the cup (1) Remove the suction cup with adapter from the plate B using a spanner. (2) Loosen the bolt (M4x8), then remove plate B from plate A. Be careful not to lose the O-ring. Completion drawing 2. Mounting of the plug Confirm the gasket seal in the plug, then mount the plugs to plate A.
For the circulating fluid piping connection, install a drain pan just in case the circulating fluid may leak. 7. Do not return the circulating fluid to the unit by installing a pump in the customer system. Breaker Operating Characteristics Common for all models 4 h 2 h 1 h 5 s 10 s 20 s 30 s 1 min 2 min 4 min 6 min 10 min 14 min 20 min 30 min Max.
Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight. 2.
KBS, KBL (P. 15-3-114, 115) 6 KBH2-R3S KBH3-R2S KBH3-R3S KBH3-R4S KBH4-R3S KBH4-R4S R 1 2 R 3 8 R 1 2 R 3 8 R 1 4 R 3 8 R 1 4 KBE2-08 KBE2-10 KBE3-08 8 10 10 8 2 Applicable tubing KBE3-10 KBE3-12 KBE4-12 12 R1 KB 1 H S Model With sealant (Male thread only) Standard specifications Female Connector Elbow Union: KBL Tube size/Connection thread size Body size T Connection thread Model KBL1-R1S
Hold the cable with a tie-band at a position close to the joint to avoid excessive force being applied to the modular jack and plug. Sensor cable Dust cover 13 Doc.No.IZ-OMK0015D 2. Installation Method 2-1.
Caution Plate A Plug(M-3P) (2 pcs.) Plate B (with O-ring) Tighten by hand, and give it an additional turn approx. 1/4 rotations with a wrench.
Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight. 2.
Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight. 2.
PFMC 7 7 A*8 8 501 5~500L/min 2 102 10~1000L/min 202 20~2000L/min *7 Rc N NPT R F G*1 1ISO228 501 102 202 04 1/2 *7 06 3/4 OUT1 OU2 *5 A NPN NPN M SI*6 B PNP PNP 5 C NPN (1~5V) SI D NPN (4~20mA) 6:L/min:L E*2 PNP (1~5V) F*2 PNP (4~20mA) 1 G*2 NPN *3 M8(3m)*4 H*2 PNP *3 2 3 N M8 *4 / ZS-40-A M8 3 m ZS-42-A PFMC7501/7102 (M352 ) ZS-42-B PFMC7202 (M352 ) -10No.PF-OMS0001CN-A M8 1
It does not comply with the Class 2 Pressure Vessel requirement. It can be used alone as a tank.
, OR connection for NPN output Brown [Red] Brown [Red] Load Black [White] Blue [Black] Black [White] Blue [Black] Switch 1 Load Switch 1 Relay Relay Switch 2 Switch 2 Relay contact Relay Switch 3 Switch 3 2-wire, with 2-switch AND connection 2-wire, with 2-switch OR connection When two switches are connected in series, a load may malfunction because the load voltage will decline when in the
If there is a risk of contact, provide safety measures such as a cover or a system that uses sensors that will activate an emergency stop before contact is made. 2. Use a balance circuit in which lurching of the piston is taken into consideration.
Consult P/A if you use a fluid other than compressed air. 2. Intermediate stops. When intermediate stopping of a cylinder piston is performed with a 3 position closed center type directional control valve, it is difficult to achieve stopping positions as accurate and minute as with hydraulic pressure, due to the compressibility of air.
), (6) of section 10.3 Ejector Assembly Replacement Procedure. 10.5 Supply (P) port One-touch Fitting Replacement A Lock pin 4 Ejector body 1 3 2 One-touch fitting (1) Remove the lock pin with a precision (3) Insert a new one-touch fitting. screwdriver. (4) Mount lock pin with a precision (2) Remove one-touch fitting. screwdriver.
Plate A Plug (M-3P) (2 pcs.)
J Use caution when handling a cylinder, which is running at a high speed and a high frequency, because the surface of a cylinder tube could get so hot enough as to cause you get burned. D-C7/C80 50 50 + 45 (n 2) 10 15 15 + 45 ( n 2) (n = 2, 4, 6) 2 D-H7/H7W D-H7NF D60 + 45 (n 2) 60 15 10 D-C73C/C80C D-H7C 15 + 50 ( n 2) (n = 2, 4, 6) -X 2 65 + 50 (n 2) 65 15 10 4.