Type: L-Shaped Table Type, Cylinder Inner Diameter(Ø): 20, Stroke(mm): 30, Max.
Type: L-Shaped Table Type, Cylinder Inner Diameter(Ø): 20, Stroke(mm): 30, Max.
Type: L-Shaped Table Type, Cylinder Inner Diameter(Ø): 20, Stroke(mm): 30, Max.
Type: L-Shaped Table Type, Cylinder Inner Diameter(Ø): 25, Stroke(mm): 30, Max.
Type: L-Shaped Table Type, Cylinder Inner Diameter(Ø): 25, Stroke(mm): 30, Max.
Type: Lubricating Device, Type: Mixing valve, Material: Die-cast aluminum / Platinum silver coated, Rated Voltage: -, Air blow circuit: Yes, Float switch specifications: -, Nozzle tube: Flexible tubes, Nozzle tube length(mm): 300, Number of mixing valves used(pcs.): -
Type: Lubricating Device, Type: Mixing valve, Material: Die-cast aluminum / Platinum silver coated, Rated Voltage: -, Air blow circuit: None, Float switch specifications: -, Nozzle tube: Flexible tubes, Nozzle tube length(mm): 300, Number of mixing valves used(pcs.): -
EX260-SEN_eng X : Thread size: M3 x 30 The following instructions must be followed during maintenance: Turn off the power supply. Stop the air supply, exhaust the residual pressure and verify that the air is released before performing maintenance. Otherwise an injury can result.
Refer to page 30 for I/O memory map details. No. Item Meaning 1 IP Address IP address of SI unit connected to Web server Force output mode enable/disable.
Val: 1 to 65000 3 Valve ON/OFF counter (Counter) 8 Disable Does not generate an error. 1: This master is valid only when "Hold/Clear priority" of the system parameter is set to Handheld. : The count is memorized every 30 seconds per channel.
Valve diagnostics 2 . 5-5 Valve diagnostics 2 Bit 0 Valve 16, 17 diagnostics 01() 1 Valve 18, 19 diagnostics 01() 2 Valve 20, 21 diagnostics 01() 3 Valve 22, 23 diagnostics 01() 4 Valve 24, 25 diagnostics 01() 5 Valve 26, 27 diagnostics 01() 6 Valve 28, 29 diagnostics 01() 7 Valve 30, 31 diagnostics 01() 36 No.EX-OMU0020CN 5.1.2.
-SMC-EX260-.xml Tightening torque 0.6 Nm 2 EX260-SPN3/SPN4 : Thread size: M3 x 30 Output number assignment Output numbering starts at zero and refers to the solenoid position on the manifold. The following instructions must be followed during maintenance: Turn off the power supply.
Proper use of the seal cap enables the enclosure to achieve IP67 specification. : Refer to page 30 for the seal cap. -11No.EX-OMV0023-A Power supply connector layout PWR: M12 5-pin plug, A-coded (SPEEDCON) No.
Otherwise malfunction can result, causing an accident. : Thread size: M3 x 30 Node ID setting No.1 Reserved Technical documentation giving detailed specification information can be found on the SMC website (URL http://www.smcworld.com). The following instructions must be followed during maintenance: Turn off the power supply.
Individual grounding should be provided close to the product with a short cable. 28 30 Hexagon socket head cap screw (M3 x 30): 2 pcs. Seal cap: (for M12 connector socket): 1 pc. Pollution degree D Side (SI unit side) NOTE Output No. 1 9 Solenoid on B side 3 5 7 17 29 31 (Note): Y connectors for external power supply are available as accessories.
LCD Liquid Crystal Display ON/OFF OFF ON SI Serial Interface Unit PLC 30 PLC ON OFF ON OFF EX600 4 LCD (H.T.)
-2No.PS-OMH0005CN-D 1 1.5 3) *3) 1 1 () -3No.PS-OMH0005CN-D () () -4No.PS-OMH0005CN-D ( ) * (10 10 ) * (13 ) FG (50N 25N ) -5No.PS-OMH0005CN-D *() 6 33 2 () () 10m DC(-)() * ( ) ( ) CE -6No.PS-OMH0005CN-D -5~50 * ON , 20~30 1% 18~27 LCD * -7No.PS-OMH0005CN-D PSE20 2 0 NPN5 + 1 PNP5 + 4C (4 ) 1 A B + 1 M SI 2 1 2 kPa MPa / ZS-26-A 2 m ZS-28-C 1 ZS-26-B (M38L 2
If the sub display is switched during the arbitrary display setting, the display will be returned to the arbitrary display 30 seconds later. (The default setting does not include arbitrary display.) NOTE If the error cannot be reset after the above measures are taken, or errors other than above are displayed, please contact SMC.
(No operation for 30 seconds after the set value change mode was selected results in automatic setting of the value appearing in the display, and set value indication returns.) 3. Press the button to move to the left digit. (If the left end digit is zero, [ ] or [ ] will flash.) [ ] means "+zero", [ ] means "-zero".
setting ( ) PF2A750 Item Default settings Hysteresis 1 Hysteresis 1 Set point 1 Set point 2 1 DC(+) 50% of max. rated flow [n_1] Input of the Set point 1 (OUT1) Selection of display mode [d_1] Display instantaneous flow PF2A711 ON Body 50% of max. rated flow 2 OUT2 [n_2] Input of the Set point 2 (OUT1) [F_1] Input the Set value of instantaneous output Unit selection function 1 [U_1] L/min 30