CL To use the lock for drop prevention purposes, the load to be attached to the cylinder must be within 35% of the cylinders holding force.
1 Be sure to read this before handling the products.
Extended periods of continuous energization Contact SMC if valves will be continuously energized for extended periods of time. Caution 1. Momentary energization If a double solenoid valve will be operated with momentary energization, it should be energized for at least 0.1 second. 2.
Even within a given allowable kinetic energy level, there is an upper limit to the size of the load that can be sustained. Thus, a horizontally mounted cylinder must be operated below the solid line, and a vertically mounted cylinder must be operated below the dotted line.
Therefore, the flow rate can be measured by detecting this frequency.
Therefore, the equipment to be connected must be below this rating.
For the analog output type, when ON the output will be 5 V or 20 mA, and when OFF, it will be 1 V or 4 mA.
Therefore, the equipment to be connected must be below this rating.
Please be sure to fill in the blank referring to page 646.
Otherwise, lock may not be engaged. u Use complete stroke or cylinder at side with lock. If cylinder piston does not reach end of stroke, lock may not be engaged or released. 2. Operating pressure Lock Caution Release Use pressures 0.15 MPa or more at port with locking mechanism. Otherwise, lock will not be released. 3.
The shorter the distance from the cylinder (the shorter the piping), the shorter the overrun amount will be, and stopping accuracy will be improved.
The larger the effective area is, the shorter the locking time will be (the overrun amount will be shorter), and stopping accuracy will be improved.
AS121FM-M5-23 AS121FM-M5-04 AS121FM-M5-06 AS221FM-01-23 AS221FM-01-04 AS221FM-01-06 AS221FM-01-08 AS221FM-02-04 AS221FM-02-06 AS221FM-02-08 AS221FM-02-10 3.2 4 6 3.2 4 6 8 4 6 8 10 22.1 22.1 22.9 27.5 27.5 27.5 32.4 34.4 34.4 36.4 43.2 8.4 9.3 11.6 9.3 9.3 11.6 15.2 10.4 12.8 15.2 18.5 17.3 17.3 18.1 20.4 20.4 20.4 25.3 25.2 25.2 27.2 33.9 12.7 12.3 7 25.1 28.8 30.1 9.6 33.8 M5 x 0.8 8 13.5
Max. 3.2 4 6 3.2 4 6 8 4 6 8 10 22.1 22.1 22.9 27.5 27.5 27.5 32.4 34.4 34.4 36.4 43.2 8.4 9.3 11.6 9.3 9.3 11.6 15.2 10.4 12.8 15.2 18.5 17.3 17.3 18.1 20.4 20.4 20.4 25.3 25.2 25.2 27.2 33.9 AS121FM-M5-23 AS121FM-M5-04 AS121FM-M5-06 AS221FM-01-23 AS221FM-01-04 AS221FM-01-06 AS221FM-01-08 AS221FM-02-04 AS221FM-02-06 AS221FM-02-08 AS221FM-02-10 12.7 12.3 7 25 25.8 22.2 9.6 28.6 M5 x 0.8 8
BA -08 BA -10 BA -32 BA -02 BA -01 CX D-G5NBL 35 40 45 45 45 40 50 45 D-G5/K5 D-B7/B8 BM1 -01 BM1 -02 BM1 -32 BM1 -04 BM1 -05 BM1 -06 Since this is a guideline including hysteresis, not meant to be guaranteed.
Be sure to operate with a drain trap installed. 7. When connecting piping to a valve, be sure to tighten while holding the valve with a wrench or other tool. 11 Series VCS Direct Operated 2 Port for Steam 2 Port Solenoid Valve for Fluid Control/Precautions 3 Be sure to read before handling Operating Environment Wiring Warning Caution 1.
The instruction manual should be carefully read and fully understood before the product is installed and operated. Also, the manual should be kept where it can be easily referred to at any time. 2. Allow space for maintenance. Allow the space necessary for maintenance and inspections. 3. Tighten screws with the proper tightening torque.
If the socket will be used again, first spread the hook outward. Connector Socket Lead wire Hook 4-4-57 58 Series SYJ300/500/700 Specific Product Precautions 3 Be sure to read before handling.
Since the products specified here are used in various operating conditions, their compatibility for the specific pneumatic system must be based on specifications or after analysis and/or tests to meet your specific requirements. Be particularly careful in determining the compatibility of the fluid to be used. 2.
Inspection and maintenance of machinery/equipment should only be performed after confirmation of safe locked-out control positions and measures to prevent danger from the fluid. 2. When equipment is to be removed, confirm the safety process as mentioned above and be certain there is no danger from fluid leakage or fluid remaining in the system. 3.