SMC Corporation of America
Elite Part Number Search
Search Results "HRS200-AN-46-AS"

[Tips] A set of thread adapters that converts the connections from Rc to NPT is enclosed as an accessory. For NPT thread, be sure to use this adapter. A set of thread adapters that converts the connections from Rc to G is enclosed as an accessory.

Model number: HRR012/018/24/030-AN/WN-10/20 The transition connector from Rc to NPT is enclosed as an accessory. For NPT piping, be sure to use this connector. Model number: HRR012/018/024/030-AF/WF-10/20 The transition connector from Rc to G is enclosed as an accessory. For G piping, be sure to use this connector.

[Tips] AN-> A set of thread adapters that converts the connections from Rc to NPT is enclosed as an accessory. For NPT thread, be sure to use this adapter. A set of thread adapters that converts the connections from Rc to G is enclosed as an accessory. For G thread, be sure to use this adapter.

Depending on the external switch output type, wire the switch to the communication connector for contact input / output (which is included as an accessory) as shown below. Mount the ferrite core (3 turns), which is included as an accessory. This is an example of wiringRefer to the Communications Operation Manual for more details.

Depending on the external switch output type, wire the switch to the communication connector for contact input / output (which is included as an accessory) as shown below. Mount the ferrite core (3 turns), which is included as an accessory. This is an example of wiringRefer to the Communications Operation Manual for more details.

Make the distance between solenoid valve and cylinder as short as possible and especially the iock-up solenoid valve should be connected to lock port as directly as possible. eLoad fluctuation during two way skoke ol rylinder can cause piston to change its speed, which makes the stop position of cylinder fluctuate.

Make the distance between solenoid valve and cylinder as short as possible and especially the iock-up solenoid valve should be connected to lock port as directly as possible. eLoad fluctuation during two way skoke ol rylinder can cause piston to change its speed, which makes the stop position of cylinder fluctuate.

No.DIG-31900-OM002 27 Auto Mode Operation Auto Mode Use an auto mode if controlling an actuator by an input current as a smart positioner. Display Switching Method at Auto Mode LCD display can be switched as follows according to Fig. 21 with the auto mode1.

Use care, as damage may occur if rotational force is applied to both ends of the piston rod. 5. Since CHQWB series does not have an air release plug, release air from components other than the cylinder (e.g. from piping, etc.) as well. 6. When mounting the cylinder body with mounting bolts, use tightening torques in the table below as a guide. 2.

160 to 179 Same as ID1 ID10 180 to 199 Same as ID1 ID11 200 to 219 Same as ID1 ID12 220 to 239 Same as ID1 240 to 249 Unused Step data input mode 250 to 253 Gateway unit control flag Numerical data input 254,255 Unused 39 - 11.2 Controller IF flagIN Data Controller IF flag is sent back to each ID ID=1 is shown below as an example [ID=1] I_Address bit 7 6 5 4 3 2 1 0 18 Abnormal station Connect

Do not use in an environment where the product is directly exposed to liquid, such as cutting oils. If cutting oils, coolant or oil mist contaminates the product, failure or increased sliding resistance can result. 3. Install a protective cover when the product is used in an environment directly exposed to foreign matters such as dust, cutting chips and spatter.

The counter-measure is as follows. Select control Circuit and solenoid valve that are of direct current drive and of good response time. Make the distance between solenoid valve and cylinder as short as possible and especially the lockup solenoid valve should be connected to lock port as directly as possible .

If using in an environment that is exposed to water splashes, please take measures such as using a cover. Do not use in an environment where moisture or water vapor are present. Otherwise failure and malfunction can result. Do not use in a place where the product could be splashed by oil or chemicals.

In cases of high piston speed, the use of an auto switch (G5NT) with a built-in OFF delay timer (approx. 200ms) makes it possible to extend the load operating time. 4. Wiring should be kept as short as possible. 3) Generally, the internal voltage drop will be greater with a 2 wire solid state auto switch than with a reed switch. Take the same precautions as in 1).

There is no problem as long as the product is used normally in an ordinary operating location. If the product is used in an environment where vibration larger than 30m/s2 or strong magnetic field is present, consult with SMC. 4.

NPN output The output type that uses an NPN transistor to operate an output device. This is also known as a positive common type since a positive potential is applied to the power supply line. NPN input Accepts a sensor output that uses the NPN transistor output signal. Number of inputs Number of points which can receive information from input equipment such as a sensor or switch.

(An assembly is shipped under the condition shown in the figure.)

An external pilot style that can be used individually is available as a made-to-order. For details, refer to the page 4-6-46.