ZR Thus, in the case of an error, each valve can be turned OFF to minimize the influences on other pads.
(An assembly is shipped under the condition shown in the figure.)
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation.
In this condition, the A port should be an SUP port and the B port an EXH port. Specify the spacer mounting position and SUP/EXH passage shut off positions on the manifold specification sheet. The spacer comes with a SUP block plate and an EXH block plate.
Do not expose the actuator motor to a magnetic field with a magnetic flux density of 1 mT or more. (1) When installing an air cylinder with an auto switch (ex. CDQ2 series) by side, maintain 40 mm minimum space around the motor.
Signal timing Check the timing of the signal from the PLC to the controller. 11.4 Controller input signal response time (P.46) When power is applied, it may take up to 10 seconds (max. 20 sec.) from SVON input to SVRE output depending on the electric actuator position. Command an operation after SVRE output is turned ON.
Operation stop Combination Symbol: D1 Combination Symbol: D4 An N.C. solenoid valve is used for the vacuum release valve. An external supply valve must be provided. An external valve must be provided to serve as the supply valve. An air operated N.C. valve is used for the vacuum release valve.
An alarm or warning is displayed when an abnormality occurs during operation. When an alarm or warning occurs, take appropriate measures according to "LECSN-T Operation Manual, Chapter 8. When an alarm occurs, the ALM is turned off. The alarm can be cleared by any of the methods marked with a circle () in the Alarm Clear column after removing the cause of the alarm.
for intermediate stop using an external stopper, etc.
(An additionally machined port will have an aluminum surface since it will be left unfinished.) Change of rotation.
It may vary substantially depending on an ambient environment.
Panel mount adapter (Part No.: ZS-46-B) Panel mount adapter + Front protective cover (Part No.: ZS-46-D) psi P ZSE20A(F) Display color OUT1 ON: Green/OUT1 OFF: Red : Arbitrary display These safety instructions are intended to prevent hazardous situations and/or equipment damage.
[F 1] Setting of OUT1 Bracket A (Part No.: ZS-46-A1) Bracket B (Part No.: ZS-46-A2) Measurement mode screen Item Default setting To obtain the operation manual about this product and control unit, please refer to the SMC website (URL http://www.smcworld.com) or contact SMC directly.
[F 1] Setting of OUT1 Bracket A (Part No.: ZS-46-A1) Bracket B (Part No.: ZS-46-A2) Measurement mode screen Item Default setting To obtain the operation manual about this product and control unit, please refer to the SMC website (URL http://www.smcworld.com) or contact SMC directly.
Its an elegant solution to an expensive problem. We have developed a new and significant cost saving procedure for laser cutting Kalrez seals from sheet stock for solenoid valve plunger assemblies.
Its an elegant solution to an expensive problem. We have developed a new and significant cost saving procedure for laser cutting Kalrez seals from sheet stock for solenoid valve plunger assemblies.
Refer to page 120 for an order example.
Do not use in an environment with oil or chemicals. Consult with SMC if an auto switch will be used in an environment laden with coolant, cleaning solvent, various oils or chemicals.
Connect the remote control cable and the switch to the connector for the contact input/output, supplied as an accessory. Then, mount the ferrite core (3 turn) supplied as an accessory. (See below) (This is an example of wiring. Refer to the Operation Manual for communication for details.)
This information is needed when contacting an SMC sales distributor. (It is an example of model "HRS040-A-20".)