Electric Actuator / Rod Type Dust-tight / Water-jet-proof (IP65 Equivalent / IP67 Equivalent) This value can be used for the selection of the power supply. 12) With lock only 13) For an electric actuator with lock, add the power consumption for the lock. 14) Excludes the controller body and the connector part on the controller side. Details of enclosure rating Enclosure rating Details Solid foreignobjects Dust-tight Dust particles are prevented from entering the device.
Standby mode When solenoid valve is turned on or the manual override is operated. (3) After adjusting pressure, lock the knob by pushing it in the arrow direction. * The state shown in (3), with the pilot valve turned on, is called "standby mode. 13 - 6. Operation and Adjustment 6-2.
Pilot port posion of the diaphragm assembly 13 VXF(A)24A** Disassembly/ Assembly Procedure For pilot valve Bonnet Hexagon socket head cap screw Spring For main body Diaphragm Bonnet Assy Hexagon socket head cap screw Spring Diaphragm Assy Assemble the pilot port position of the diaphragm assembly as shown in the figure below. Pilot port Pilot port Fig.
Decline in the power supply voltage. (13) (7) AC voltage is applied to the DC pilot valve. The pressure does not increase even if the signal pressure is increased. Pressure cannot be adjusted (14) Insufficient supply pressure and pilot pressure Air is consumed by the equipment on the secondary side.
Failure due to buzzing sound Foreign matter is caught in the iron cores. (4) Wear of the iron cores Decline in the power supply voltage (13) -109 VT307-OMQ0002-B Countermeasures No.
Buzzing noise Foreign matter caught in the armature (4) Wear-out of armature Decline in the power supply voltage (13) 10 VT317-OMH0001-B Countermeasures No.
Leakage due to deterioration of rubber parts Consult SMC. 9 -13- Doc. no.
Troubleshooting 13 8. Assembly drawing 14 -1- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
(See Fig.13) Replacement part: Shock absorber Bore size Part no. 32 RB1007-X225 4050 RB1407-X552 Lever Hexagon socket head set screw Push down Fig. 11 10 - Lever Shock absorber 11.Internal construction 12 16 Push down Replacement Grease applied Approx.5mm Fig. 12 Fig.13 20 11 - 32&50 Component Parts (12&50) 12 - Revision history 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81
EX600-SEN3 (PNP output) -common type valve EX600-SEN4 (NPN output) +common type valve 13 The valve dose not work correctly Polarity of output does not match. SI unit has failed. Replace the SI unit with a normal one, and check the operation. Valve failure. Replace the valve with a normal one, and check the operation.
D E F G H I ZS-31-X188 20 9 R1/8 R1/8 14 1.5 ZS-31-X189 20 9 NPT1/8 NPT1/8 14 1.5 ZS-31-X175 29 13 R1/4 R1/4 17 1.6 ZS-31-X186 29 13 NPT1/4 NPT1/4 17 1.6 -14No.PS-OMG0006-D Revision history A: For B: Complete revision C: Contents revised in several places. D: Contents revised in several places.
EX600-SPN1 (PNP output) 13 Abnormal valve operation Polarity of output does not match. Negative common type valve EX600-SPN2 (NPN output) Positive common type valve SI unit has failed. Replace the SI unit with a normal one, and check the operation. Replace the valve with a normal one, and check the operation. Or refer to the troubleshooting of the valve used.
Dimensions of the regulator with the bottom exhaust direction [IR30*0-A] -13- 8-2.
Troubleshooting 13 8. Assembly drawing 14 -1- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
ON (0: OFF, 1: ON), and the output number starts at zero from LSB (least significant bit). (3) Fuse disconnection details The power supply fuse disconnection for the SI unit solenoid valves can be monitored by the link special register of the master station. 0: Normal 1: Fuse disconnected Buffer area of master station Example: QJ61BT11N b15 b14 b13 b12 b3 b2 b1 b0 (688H)SW0088 16 15 14 13
(See I/O Configuration (page 19) for details.) -15No.EX-OME0014-F Diagnosis information Diagnosis information of the SI unit is composed of 6 bytes standard diagnosis information and 7 bytes SI unit status information, 13 bytes in total, as specified in PROFIBUS DP.
Temperature Alarm b 8 contact (CLOSE During Alarm) 3 Resistance Bulb Terminal A 8 1 4 Resistance Bulb Terminal B External temperature 5 Resistance Bulb Terminal B 15 9 sensor D-sub 15 pin (Socket type) connector 15 FG Fixed screw: M2.6 HEC002-A/HEC006-A 10-1 Appendix 10.2 Calculation of dew point (from psychometric chart) Relative humidity (%) 55 100 90 80 70 60 50 45 40 B A 35 30 4 10 13
If the problem is not improved, contact your SMC sales representative. (13) If pressure gauge is used in the direction as Figure 1, it may cause displacement from zero point. Therefore, be sure to use pressure gauge in the Direction as Figure 2 Zero point Up Zero point Down 13 - 5.Warranty 1.
Therefore, replace the product with a new one. (13) Pay attention to the motion of the actuator at the time of restart after the release of residual pressure. When restarting the product after releasing the residual pressure, check the initial driving direction, confirm that the work area is secured, and then restart the product.
The buttons cannot be operated. 13 Product failure Replace the product. 1. Confirm that the mounting adapter for the regulator is installed properly. Incorrect installation Correct the mounting conditions. The body has become loose. 2. Confirm that the Pressure switch is 14 installed to the mounting adapter properly. Product failure Replace the product.