Series SY100 3 Port Solenoid Valve Rubber Seal

Lead wire Hook Caution Plug Connector Lead Wire Length Gently operate locking manual override styles B, D using small screwdriver. [Torque: 0.1Nm or less] Standard length is 300mm, but the following lengths are also available.

NAMUR Interface 3 Port Solenoid Valve VFN200N Series [Option]

How to Order VFN212 02 N 5 F D Z CE marking NAMUR Interface Nil Q CE marked product Voltage Thread type 1 100 VAC, 50/60 Hz 2 200 VAC, 50/60 Hz 3 110 to 120 VAC, 50/60 Hz 4 220 VAC, 50/60 Hz 5 24 VDC 6 12 VDC 7 240 VAC, 50/60 Hz Nil Rc (PT) F G (PF) N NPT Electrical entry Solenoid G Grommet E Grommet terminal T Conduit terminal D DIN terminal Nil Single solenoid D Double solenoid Manual

5 Port Pilot Operated Solenoid Valve Series VFR2000 Rubber Seal, Plug-in/Non Plug-in How to Order Option Port size (P, A, B port) Thread type Electrical entry Rc Nil Nil Nil None Without sub-plate F: Plug-in type 01 1 8 F Z G With light/surge voltage supp

VQC 1 2 3 100 VAC, 50/60 Hz 200 VAC, 50/60 Hz 3 Electrical entry VQZ 110 to 120 VAC, 50/60 Hz G: Grommet E: Grommet terminal T: Conduit terminal D, Y: DIN terminal 4 3 position exhaust center 220 VAC, 50/60 Hz 5 6 24 VDC 12 VDC SQ 4 7 240 VAC, 50/60 Hz Note) VFS 9 Other 3 position pressure center Option Note) L and M plug connectors: Max. 220 VAC VFR 5 L: L plug connector M: M plug

VG342

Electrical entry G Grommet D DIN terminal X T Conduit terminal E Grommet terminal 1489

High Vacuum Slit Valve

one for C open and close) F D-sub connector (CDE-9PF05 : Hirose Electric Co.

E-P HYREG ® Series VY1

If it must be installed in an environment with poor noise conditions, eliminate the power supply noise by using a line filter, Z-wrap, or a spark killler on the 100 V power supply or signal source line. The length of the power suply and signal lines must be kept as short as possible.

Magnet Gripper Unit for Collaborative Robots

Polyurethane tube for piping 4 (TU0425BU-100) 2m Conversion cable 1pc. 4 - 2.

IDX-OM-W034

SIZE PORT SIZE B G H D E WITH LAMP SWITCH DRAFT AIR OUTLET THERMOMETER EVAPORATION BALL VALVE BLOCK TERMINAL AUTO DRAIN F C VENTILATION VENTILATION [DIA.911]) (WIRE DIA.0.4 ENTRY HOLE POWER CORD DRAIN TUBE LENGTH39.4[1000] J N M K L P [4XDIA.13] 4XDIA.0.5 (SIZE OF RECOMMENDED BOLTM10) A B C D E F G H J K L M N P Q R Model Port Size Dimensions (inch [mm] ) 31.5 [800] 34.2 [868] IDFB55E 2 1.4

KFx-OM00002

Minimum clearance6mm 100 2d D L 1 = Caution Mandrel (1) Preparation before piping Before piping is connected, the mounting surface of the female thread should be thoroughly cleaned out with air (flushing) or washed to remove chips, cutting oil and other debris from inside the pipe. (2) Check the model, type and size before installation.

KFx-OMY0077

Refer to the recommended piping conditions. (4) Do not apply unnecessary forces such as 100 2d D L 1 = Mandrel twisting, pulling, moment loads, vibration and impact, etc. on fittings or tubing. This will cause damage to the fittings and will crush, burst or release tubing. 5 - 2.

Compact Slide ø 6, ø 10, ø 16, ø 20 MXH Series

V 100 V or less Relay, PLC 2-wire 12 V No 1 Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance.

Pneumatic Positioner IP300/IP3100

INSTALLATION B D Installation Transmission Din & Feed-back lever Fig. SINGLE-ACTING ACTUATOR SIGNAL PRE-Y%i-rpur SIGNAL RANGE INSTALLATION STYLE IREF. FIG. 1) OUT 1 OUT2 Direct ? OPEBATION ACTUATOR 315 DSi used pruggeo 1/2 Solit D c pruggeo used 1/2 Solit B 3-15 osi c USEO plugged '1l2 Solit B 3-15 nsi pruggeo used '112 Solit D Fig. Reverse = ) Y INSTALLATION STYLE (REF.

Large Type Vacuum Unit Series ZR

1 85 80 PD Rc(PT) 1/8 port PV (vacuum pump connection port) SMC 2-4.2 (mounting hole) PS 51.5 41.5 2 20 32.5 27.5 Filter block D 16.5 16 PV 2 8 13 3 1.5 Adapter G 1 4 Bracket A Bracket A 128.7 100.8 (9.8) 4.5 Rc(PT) 1/8 port V (vacuum pad connection port)

KFx-OMV0011

Also, when the sealant tape is used, leave approximately 1 thread ridge exposed at the end of the threads. 100 2d D L 1 = Mandrel 5 - 2. Specific Product Precautions (2) (3) Check the model, type and size before installation.

D. P. Lube (Unit) Series ALD(U)600/900

(Connection port center) (Connection port center) F (Bracket mounting dimensions) Bracket (Option) B C A INA-11-402 INA-11-403 INA-11-404 INA-11-405 INA-11-406 INA-11-407 Model Port size Rc 4 1 63 63 80 85 90 100 141 164.5 170 180 230 251 15 15 15 20 22 22 8 3 , , 8 3 4 1 2 1 Bracket dimensions E C D B A Model Port size 4 3 F 345 419.2 G 32.5 0 H 95 120 J 14 14 K 57 49.6 1 1 , 87.5 125 4

This is a legacy product. Please contact us for the latest version.sales@ocaire.com, CYL, TIE ROD, LOCKING, ACTUATOR, CLA/CLA2 TIE-ROD CYLINDER, SE, 100MM CLA DBL-ACT AUTO-SW, 46.29707 lb

This is a legacy product. Please contact us for the latest version.sales@ocaire.com, CYL, TIE ROD, LOCKING, ACTUATOR, CLA/CLA2 TIE-ROD CYLINDER, SE, 100MM CLA DBL-ACT AUTO-SW, 30.10687 lb

This is a legacy product. Please contact us for the latest version.sales@ocaire.com, CYL, TIE ROD, LOCKING, ACTUATOR, CLA/CLA2 TIE-ROD CYLINDER, SE, 100MM CLA DBL-ACT AUTO-SW, 30.49333 lb

This is a legacy product. Please contact us for the latest version.sales@ocaire.com, CYL, TIE ROD, LOCKING, ACTUATOR, CLA/CLA2 TIE-ROD CYLINDER, SE, 100MM CLA DBL-ACT AUTO-SW, 35.60465 lb

This is a legacy product. Please contact us for the latest version.sales@ocaire.com, CYL, TIE ROD, LOCKING, ACTUATOR, CLA/CLA2 TIE-ROD CYLINDER, SE, 100MM CLA DBL-ACT AUTO-SW, 33.44219 lb