5 Port Solenoid Valve Series SV AS2200-01 200 100 70% 50% 30% 10% 0 400 MB 40 300 Stroke mm AS2201F -02-08 AS2200-02 200 100 0 ANA1 -C10 T0806 400 MB 50 300 Stroke mm AS3201F -02-08 AS3000-02 200 100 0 400 MB 63 300 Stroke mm AS4000-03 200 100 0 Solenoid valve Silencer Tubing Speed controller 200 300 400 500 600 700 800 900 1000 1100 1200 Speed at the end mm/s Applicable related components For details regarding different
Sufficient vacuum suction may not be achieved in presence of any clearances. X Clearance Opening 838
M Weight (g) AS221F-U01-23 AS221F-U01-04 AS221F-U01-06 AS221F-U01-08 AS221F-U01-10 AS221F-U02-04 AS221F-U02-06 AS221F-U02-08 AS221F-U02-10 AS321F-U02-06 AS321F-U02-08 AS321F-U02-10 AS321F-U02-12 AS321F-U03-06 AS321F-U03-08 AS321F-U03-10 AS321F-U03-12 AS421F-U04-10 AS421F-U04-12 Model Applicable tubing O.D. d 3.2 4 6 8 10 4 6 8 10 6 8 10 12 6 8 10 12 10 12 27.9 28.2 29.6 32.4 40.2 32.5 33.1
ASD Model Meter-out type Rod and applicable tubing O.D. 4 6 8 10 Meter-in type AS1000P-04-04 AS2000P-04-04 AS2000P-06-06 AS2500P-06-06 AS3000P-08-08 AS3000P-10-10 AS1010P-04-04 AS2010P-04-04 AS2010P-06-06 AS2510P-06-06 AS3010P-08-08 AS3010P-10-10 AS AS-FE KE
(In case of output OUT2, n_1, 2 to be n_3, 4 and P_1, 2 to be P_3, 4.)
(Tightening torque of M3 screw should be 0.5 to 0.7 Nm.) 5. Modification of the detecting position should be made in the condition of 3. Auto Switch Mounting Bracket Part No.
Warranted repair shall be on request basis. Unrequited repair shall be provided in accordance with the warranty period, preconditions and terms defined above. Therefore, the repair service shall be available on a chargeable basis if a failure is detected after the warranty period.
used. determine whether or not the product can be used. determine whether or not the product can be used. determine whether or not the product can be used. determine whether or not the product can be used. 3.
Warranted repair shall be on request basis. Unrequited repair shall be provided in accordance with the warranty period, preconditions and terms defined above.
The switch may be damaged if a screw other than the one supplied, is used.
Avoid applications in which two or more cylinders with end lock are synchronized to move one workpiece, as one of the cylinder locks may not be able to release when required. 6. Use a speed controller with meter-out control. Lock cannot be released occasionally by meter-in control. 7. Be sure to operate completely to the cylinder stroke end on the side with the lock.
Be sure to take appropriate protective measures if the product is to be used in an environment where it will be constantly exposed to water or fluids other than water splash. In particular, the product cannot be used in environments where oils, such as cutting oil or cutting fluid, are present.
The larger the effective area is, the shorter the locking time will be (the overrun amount will be shorter), and stopping accuracy will be improved. 3. Place the solenoid valve for unlocking close to the cylinder, and no farther than the cylinder drive solenoid valve.
Application requirements should be considered for appropriate model selection. Adsorption Confirmation Sensor installed close to the pad 1 Sensor installed close to the pad 2 PSE511 + PSE100 PS1100-R06L Pad adsorption can be confirmed easily. Response delays, caused by piping, will not be a factor due to the close proximity of the sensor to the pad.
Give us a call today and discover just how amazing SMC Serial Network system can be.
A manifold equipped with a valve or a block assembly can be mounted on the DIN rail. However, a serial connector block assembly cannot be mounted on the DIN rail when it is connected with another block; the serial connector block must be mounted separately. (FREE cannot be seen.) Valve lock switch [Locked] Press the manifold.
Use a 3 wire switch if this specification will not be satisfied. Moreover, leakage current flow to the load will be "n" times larger when "n" auto switches are connected in parallel.
Also, the surge pressure must be under the maximum operating pressure.
Otherwise, lock may not be engaged. u Use complete stroke or cylinder at side with lock. If cylinder piston does not reach end of stroke, lock may not be engaged or released. 2. Operating pressure Lock Caution Release Use pressures 0.15 MPa or more at port with locking mechanism. Otherwise, lock will not be released. 3.