CV/MVGQ

Do not loosen the cushion valve more than 2 turns from the fully closed state. Do not loosen it more than 2 turns because this could cause the cushion valve to be ejected. RE A B REC Caution CX Do not use an air cylinder as an air-hydro cylinder, because this could result in oil leakage. Do not twist the rod boot during installation.

C95

When in a locked condition, do not apply a load accompanied by an impact shock, strong vibration or turning force, etc.

1

Do not operate Series CS1 at twice the output. CJ1 CJP Applicable Series CJ2 Series Vol. no.

MGG

(Do not tighten it with pliers or other tools.) BA 32 BA 04 BA 05 BA 06 BA 08 BA 10 BA 01 BA 02 BM1 01 BM1 02 BM1 32 BM1 04 BM1 05 BM1 06 The following stainless steel mounting screw kits (including set screws) are available for use depending on the operating environment. (Order the mounting band separately, as it is not included.)

pa

Do not apply heat cycle.) Operating fluid temperature 0 to 100C (Not be frozen. Do not apply heat cycle.)

Cylinder with lock

Fig. 2 Center of gravity of the load mounted to the rod end Do not scratch or dent the sliding parts of the piston rod. Damage to the seals may lead to air leakage and locking failure. Do not apply loads with impact, strong vibration or rotational force while the lock mechanism is activated.

MNB

B Z + Stroke DB DX DD 90 B 4DT A DS DH 4DR DB DU DO DO DC DE DU DL Rotation (mm) No.

IDX-OM-X004

Do not connect the earth to a water pipe, a gas pipe, or a lightening rod. Do not plug too many leads into a single socket. That causes exothermic heat or fire. Do not convert the wiring to use.

Free Mount Cylinder

(mm) 02 04 06 08 10 13 16 20 25 32 40 50 2 4 6 8 10 13 16 20 25 32 40 50 Pad type 02 04 06 08 10 13 16 20 25 32 40 50 2 4 6 8 10 13 16 20 25 32 40 50 Pressure gauge position Thread dia.

SYJ Series

Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 5. If the volume of air leakage increases or the valve does not operate normally, do not use the valve. Perform periodic maintenance on the valve to confirm the operating condition and check for any air leakage. 5.

Cylinder with Lock

Do not turn the piston rod with the rod boot kept locked. When turning the piston rod, loosen the band once and do not twist the rod boot.

HRX-OM-X010

Do not work when intoxicated or feeling ill. Accidents may occur if disregarded. Do not remove a panel unless permitted in this manual.

HRX-OM-I051

Do not remove cover panels that are not designated in this manual.

/

For AC specifications, Nil is only set for electrical entry DO.

Title not found

I %sillrc SERIES NCJ2 Standard Type: Single Acting/ Spring Extend Spring Extend/Rod Side Flange Type (F) rucrzr lEi," F4-l sr'or,Jl r NCJ2F6 Rod Cover Head Cover NCJ2Fl0, 16 .sE (114") a10 o16 (5i8") BORE SIZE .06 l'v4"t s10 (3/8") o16 (5/8") * In case of auto switch with 06 bore, add smm to S and Z. Spring Extend/Double ClevisType (D) r.rcJzo [e*" "i'"F] qE6] r ocDaSocr?

Air Cylinder NCJ2 Series Miniature Stainless Steel Body

%sillrc I SERIES NCJ2 Standard Type: Single Acting/ Spring Extend Spring Extend/Rod Side Flange Type (F) rucrzr lEi," F4-l sr'or,Jl r NCJ2F6 Rod Cover Head Cover NCJ2Fl0, 16 .sE (114") a10 o16 (5i8") BORE SIZE .06 l'v4"t s10 (3/8") o16 (5/8") * In case of auto switch with 06 bore, add smm to S and Z. Spring Extend/Double ClevisType (D) r.rcJzo [e*" "i'"F] qE6] r ocDaSocr?

Clean One-touch Fittings For Driving Air Piping KPQ/KPG Series

Do not repair or patch the replaced tubing or fittings for reuse. 1. Do not use in environments or locations where there is a danger of damage to fittings and tubing. For fitting and tubing materials, refer to specifications and construction drawings, etc. 2. Provide shade in locations which receive direct sunlight. Caution 1.

PFA/PFW

Do not wire with power lines or high voltage lines. Wire separately from power lines or high voltage lines, avoiding parallel wiring or wiring in the same conduit with these lines. Control circuits, including switches, may malfunction due to noise from these other lines. 5. Do not allow short circuiting of loads.

ASR

Do not make any modifications to be product. Do not take the product apart. Piping Caution 1. Before piping Make sure that all debris, cutting oil, dust, etc, are removed from the piping. 2. Wrapping of pipe tape When screwing piping or fittings into ports, ensure that chips from the pipe threads or sealing material do not get inside the piping.

HRX-OM-K003

Do not work when intoxicated or feeling ill. Accidents may occur if disregarded.