TUS

The value of the minimum bending radius is measured at the temperature of 20C as shown in the figure on the right. 4. Use inner sleeve, taking the removing force into consideration when used with One-touch fittings.

Polyurethane Tubing TU/TIUB Series

Silver (S1) MS Solid yellow (Y1) Clear yellow (Y2) KKA Neon yellow (Y3) KP Clear orange (YR1) Neon orange (YR2) LQ Nominal size (inch) 1 4 " 3 16" 1 8 " 3 8 " 1 2 " 5 32" 5 16" MQR Nominal size (mm) T T 3.2 IDK Fluid Air/Water 20C 0.8 Max. operating pressure (MPa) Bend the tube into U-form at a temperature of 20C. Fix one end and close loop gradually.

VER2000/4000

JIS Symbol Proportional Solenoid Specifications 1 A VEA25 Applicable power amplifier Max. current 13 (Ambient temperature 20C) Coil resistance 4(A) 4(A) 5(R1) 1(P) 3(R2) 5(R1) 1(P) 3(R2) 13 W (Ambient temperature 20C, with maximum current) Rated power consumption 2 (B) 2 (B) Coil insulation type Class H or equivalent (180C) Max. temperature rise 140C (Ambient temperature 50C, with maximum

4 Port Solenoid Valve Common Specifications Series SJ2000/3000

Note AXT100-DS25-015 AXT100-DS25-030 AXT100-DS25-050 1.5 m 3 m 5 m Conductor resistance /km, 20C 65 or less Cable 25 cores x 24AWG Withstand pressure V, 1 min, AC 1000 For other commercial connectors, use a 25 pins type with female connector conforming to MIL-C-24308. Insulation resistance Mkm, 20C 5 or less Note) The minimum bending radius for D-sub connector cables is 20 mm.

/

How to Calculate Minimum Bending Radius Burst Pressure Characteristics Curve and Operating Pressure 4.0 2R 3.0 Fixed end Pressure (MPa) Burst pressure 2.0 1.0 Maximum operating pressure Bend the tube into U-form at the temperature of 20C. Fix one end and close loop gradually.

SZ3000

Item Conductor resistance /km, 20C Characteristics Cable length (L) Assmbly part no. Note Connector manufacturers example Hirose Electric Co., Ltd. Sumitomo 3M Limited Fujitsu Limited Japan Aviation Electronics Industry, Ltd. J.S.T. Mfg.

Angle Seat Valve

Subsonic flow : Flow greater than the critical pressure ratio Standard condition : Air in a temperature state of 20C, absolute pressure 0.1 MPa (= 100 kPa = 1 bar), relative humidity 65%. It is stipulated by adding the (ANR) after the unit depicting air volume.

ISG

Contacts/Bulb gland Pressure Source Nil W Nil B C 1a1b (Standard) 2ab Contact Warning Enclosure Type A 20a (Standard) Type A 20b Type A 20c Bulb gland 1.

Wear Resistant Tubing Series TUZ

How to Calculate Minimum Bending Radius Burst Pressure Characteristics Curve and Operating Pressure 4.0 2R Fixed end 3.0 Pressure (MPa) Burst pressure 2.0 1.0 Maximum operating pressure Bend the tube into U-form at the temperature of 20C. Fix one end and close loop gradually.

Thermo-chiller Series HRS Compact Type (Except HRS050)

Note 4) q Ambient temperature: 25C, w Circulating fluid temperature: 20C, e Rated circulating fluid flow rate, r Circulating fluid: Clear water, t Facility water temperature: 25C Note 5) Use a 15% ethylene glycol aqueous solution if operating in a place where the circulating fluid temperature is 10C or less.

Speed Controller with Residual Pressure Release Valve with One-touch Fitting Series AS



FE Elbow Type/Universal Type

Metric size 4 4 6 230 260 390 460 660 790 920 1580 1710 Flow rate (/min (ANR)) 180 Controlled flow (Free flow) Flow Direction Symbols on Body Effective area (mm2) 2.7 3.5 4 6 7 10 12 14 24 26 Meter-out type Meter-in type Note) Flow rate values are measured at 0.5 MPa and 20C.

0.55

(Coil temperature: 20C, at rated voltage, without surge voltage suppressor) Note 2) This solenoid valve requires lubrication. Use turbine oil Class 1 (ISO VG32).

Pilot Operated

Solenoid Coil Specifications Note) The values are for an ambient temperature of 20C and at the rated voltage.

7.5

Note AXT100-DS25-015 AXT100-DS25-030 AXT100-DS25-050 1.5 m 3 m 5 m Conductor resistance /km, 20C 65 or less Cable 25 cores x 24AWG Withstand pressure V, 1 min, AC 1000 For other commercial connectors, use a 25 pins type with female connector conforming to MIL-C-24308. Insulation resistance Mkm, 20C 5 or less Note) The minimum bending radius for D-sub connector cables is 20 mm.

ALF400 to 900, ALT-5/-9

Burst pressure Burst pressure (MPa) Note) Min. bending radius (mm) 24 20C to 60C Operating temperature Material Nylon 12 Note) The value at temp. of 20C and with O.D. variable rate 10% max.

Process Pump Series PA3000/5000/PAX1000 Series PB1000

Membrane Dyer Series IDG Standard specifications/Single style (standard dew point 20C (4F)) Model Standard dew point 20C IDG5 IDG10 IDG20 IDG30 IDG50 Fluid Compressed air Macromolecular membrane dryers that act like filters Range of operating conditions Standard performance conditions Inlet air pressure MPa (psi) 0.3 to 0.85 (43 to 123) 0.3 to 1.0 (43 to 145) Inlet air temperature C (F) Note

Process Pump Series PA3000/5000/PAX1000 Series PB1000

Membrane Dyer Series IDG Standard specifications/Single style (standard dew point 20C) Model Standard dew point 20C IDG5 IDG10 IDG20 IDG30 IDG50 Fluid Compressed air Macromolecular membrane dryers that act like filters Range of operating conditions Standard performance conditions Inlet air pressure MPa 0.3 to 0.85 0.3 to 1.0 Inlet air temperature C Note 1) 5 to 55 Ambient temperature C 5

5 Port Solenoid Valve/Body Ported, Cassette Type Manifold, Series SZ3000

Response Time Note) Based on JISB8375-1981 dynamic performance test (with coil temperature of 20C and at rated voltage).

Stainless Steel High Vacuum, Angle/In-line Valve, Angle type Series XM, In-line type Series XY

Residence time of water at 20C is 5.5 x 10-6sec, whereas at 150C is 2.8 x 10-8 sec, or 200 times shorter.

Clean Air Module

Real-time switch output Hysteresis mode ON Flow rate conversion YES OFF P-1 P-2 Normal condition {0C, 101.3 kPa, Dry air} or standard condition (ANR) {20C, 101.3 kPa, 65% RH} can be selected.