3 300 200 100 20 200 400 600 800 1000 25 200 400 600 800 1000 1200 1400 Flow rate Q [kg/h] ( ): Saturated steam holding heat (kcal/kg) ( ): Saturation temperature (C) For Water How to read the graph The pressure differential to generate a flow rate of 25 L/min water is as follows.
3 Port Air Operated Valve Series VZA200/400 Fluid Air 1 2 1 2 VZA4 2, 4 4 1 2 1 2 VZA2 2, 2 4 1 2 1 2 VZA4 2, 4 4 1 2 1 2 Operating pressure range (MPa) 0.1 to 1.0 0.15 to 1.0 VZA2 2, 2 4 0.1 to 1.0 0.15 to 1.0 Pilot pressure range (MPa) Impact/Vibration resistance (m/s2) Note) 150/50 Operating pressure Pilot pressure Note) Impact resistance: No malfunction from test using drop impact tester
Maximum manufacturable stroke (mm) Bore size (mm) Standard stroke (mm) 10 50, 100, 150, 200, 250, 300 500 15 50, 100, 150, 200, 250, 300, 350, 400, 450, 500 750 25 100, 150, 200, 250, 300, 350, 400, 450, 500, 550, 600 1200 The stroke is available in 1 mm increments with the maximum stroke as the upper limit. For a stroke in the standard stroke range, suffix the part number with -XB10.
P16 s1 s1 s1 s1 s2 s2 s2 s2 ... ... ... ... s32 s32 s32 s32 0.5mm) 1 2 , 2. 30mm 30mm 3.
P16 S1 S1 S1 S1 S2 S2 S2 S2 ... ... ... ... S32 S32 S32 S32 0.5mm) 1 2 2. 3.
/s2 (Without pressure sensor and pressure switch, With pressure sensor) Impact resistance Note 2,3) 100m/s2 (With pressure switch) Standard CE, RoHS Note 1) The characteristics are satisfied when tested for 2 hours in each of the X, Y and Z directions at 10 to 500 Hz without energization.
switch) 150m/s2 (Without pressure sensor and pressure switch, With pressure sensor) Impact resistance Note 2,3) 100m/s2 (With pressure switch) Standard CE, RoHS Note 1) The characteristics are satisfied when tested for 2 hours in each of the X, Y and Z directions at 10 to 500 Hz without energization.
Do not drop, bump or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the auto switch may not be damaged, the inside of the auto switch could be damaged and cause a malfunction. 2. Mount auto switches using the proper tightening torque.
The station address is set using the rotary switches S1 and S2. (1) Settings of the Rotary Switches S1 and S2 Set the station address using the rotary switches S1 and S2.
The vacuum aspiration fluence shows the fluence immediately before piping in the actuator. 5 - 3.How to Order 11LEJS 40 A 500 S2 1 10 9 8 7 4 5 3 2 6 *1 (2) Motor type (3) Lead [mm] (1) Size 40 LEJS40 LEJS63 Output [W] Actuator size Compatible controller Type 63 16 A 20 AC servo motor (incremental encoder) S2 10 8 B LECSA-S1 40 100 (5) Motor option AC servo motor (incremental encoder) S3
m/s2) *3 100 *1: Values are based on standard of SMC measurements.
This reduces noise considerably compared with A much lower air consumption is required than the current model. the current model. 1: Conditions: Unseated for 5 seconds and seated for 20 seconds (For G type) Comparison of detection circuit ISA3 New New Current model (ISA2) A B EXH port EXH port P1 Sensor Sensor SUP port S1 S3 SUP port S2 Sensor S1 S4 S2 Detection port P2 Detection port C D
Refer to page 714.) 25 or less 40 or less 5 3 Fluid 2 position single 2 position double 3 position Operating pressure range MPa Ambient and fluid temperature Response time ms (0.5 MPa) Max. operating frequency (Hz) Manual override (Manual operation) Pilot exhaust method Lubrication Mounting orientation Impact/Vibration resistance m/s2 Note 1) 2 position single, double 3 position 2 position
H5 Initial power / Power consumption (W) 100 VAC 200/40 400/70 400/80 600/130 800/180 200 VAC 800/40 1600/80 1600/80 2400/130 3200/180 Note 1) Initial power and power consumption are nominal values. Note 2) Heaters are not available for size 16.
H5 Initial power / Power 100 VAC 200/40 400/70 400/80 600/130 800/180 200 VAC 800/40 1600/80 1600/80 2400/130 3200/180 consumption (W) Note 1) Initial power and power consumption are nominal values. Note 2) Heaters are not available for size 16.
Laser marking Hexagon wrench Features 2 Rodless Cylinder for Vacuum Series CYV How to Order CYV 15 200 Rodless cylinder for vacuum Standard stroke Bore size 15 32 15mm 32mm Standard stroke (mm) 100, 150, 200, 250 300, 350, 400, 450 500, 600, 700 Bore size (mm) 15, 32 Specifications 15 32 Bore size (mm) Atmosphere to 1.3 x 10Pa (ABS) Operating environment pressure Air and inert gases Operating
Relief port size M5 x 0.8 Piston speed 50 to 400 mm/s Mounting Basic style, Axial foot style, Rod side flange style Head side flange style Auto switch can be mounted.