CL Single Knuckle Joint I-G02/G03 Material: Rolled steel I-G04 Material: Cast iron Y-G02/G03 Material: Rolled steel Y-G04 Material: Cast iron NDH10 (Hole dia.) NDH10 MM MM L L RR1 E1 E1 A1 U1 NX NZ NX L1 NZ A Applicable bore size (mm) A A1 E1 L1 MM U1 NX NZ L Applicable bore size (mm) Applicable pin part no. Part no. NDH10 Part no.
1 Fine Lock Cylinder with Guide Series MLGC 20, 25, 32, 40 A linear transfer cylinder unit with a built-in locking mechanism and a guide rod integrated in a compact design.
1 Fine Lock Cylinder with Guide Series MLGC 20, 25, 32, 40 A linear transfer cylinder unit with a built-in locking mechanism and a guide rod integrated in a compact design. CL CL1 MLGC CNG MNB CNA CNS CLS CLQ MLGP RLQ MLU ML1C High level of stopping accuracy D-X Locking method Spring locking Pneumatic locking Spring and pneumatic locking 20Locking in both directions is possible.
Since a large quantity of liquid will be pumped out, use a suitable throttle in the discharge port if problems occur. Note 3) With a low number of operating cycles, even a valve with a small Cv factor can be operated.
Since a large quantity of liquid will be pumped out, use a suitable throttle in the discharge port if problems occur. Note 3) With a low number of operating cycles, even a valve with a small Cv factor can be operated.
Since a large quantity of liquid will be pumped out, use a suitable throttle in the discharge port if problems occur. Note 3) With a low number of operating cycles, even a valve with a small Cv factor can be operated.
Modify the detecting position while the auto switch is secured at the position of (3) in the figure. a Auto switch mounting screw M3 x 0.5 x 8 L (For BQ-1) Auto switch Set screw (Unused) r u t c e y Auto switch mounting bracket d Auto switch mounting screw M2.5 x 0.45 x 6 L b Square nut (For BQ-1) w Cylinder q BQ-1 and BMU1-025 are a set of a and b shown above.
When ordering a valve with a lead wire of 600 mm or longer, be sure to indicate the model number of the valve without connector and connector assembly. A-C ON Orange P A P A Orange OFF A R B-C ON (Reset) A R Green 4-12-4 5 Series VQ100 Precautions Be sure to read before handling. For Safety Instructions and Solenoid Valve Precautions, refer to page 4-18-2.
Body Size: 20, Thread: Rc (Rc: for Sizes 20, 25, 30, 40; M5: for Size 10), Port Size: 02 (1/4), Option: w/o Mounting Option, w/o Pressure Gauge, Semi-Standard: Standard
Regulator, Pressure Boosting Valve: Regulator, Regulator Type: Standard, Shape: Standard, Operating Environment: Standard, Compatible Fluid: Air, Exhaust Mechanism (Air Bleed): [Included] Relief, Reverse Flow Function (Relief): No, Supply Side Connection Type: Rc, Supply Side, Connection Diameter: 1/4, Flow Direction: [Right] From Left to Right, Control Side Connection Type: Rc, Control Side
Series VQZ base mount solenoid valves combine convenience with durability and performance in a more traditional mounting style.
Note 2) Use caution not to tighten excessively when mounting a pressure gauge, otherwise it may result in a breakdown. Use a pipe tape for sealing. Recommended torque: 12 to 14 Nm.
Regarding a vacuum switch valve and a vacuum release valve If a non-vacuum valve is installed in the middle of piping system having a vacuum, the vacuum condition will not be maintained. Use a valve designed for use under vacuum condition. 10.
Valve mounting direction Stations 02 Single solenoid coil is on opposite side as the A, B port. 2 stations Nil + + A + + + + + : : R P P R R port M5 x 0.8 R port M5 x 0.8 Single solenoid coil is on same side as the A, B port.
For connector cable of M8 connector, refer to page 90. 25 Series SYJ5000 Construction 2 position single 2 position double (A) 4 (B) 2 (A) 4 (B) 2 5 (R1) 3 (R2) 1 (P) 5 (R1) 3 (R2) 1 (P) e w q t r q y t rw (A) 4 (B) 2 (A) 4 (B) 2 i 5 (R1) 1 (P) 3 (R2) 5 (R1) 1 (P) 3 (R2) i u 3 position closed center/Exhaust center/Pressure center 3 position closed center (A) 4 (B) 2 q t rw 5 (R1) 3 (R2) 1
range. 03Data field of a command is not normal.
M L2 Pressure range Option 3 Symbol Description ISE70 0 to 1 MPa ISE71 0 to 1.6 MPa Symbol Description Nil Operation manual Y None K Operation manual + Calibration certificate Piping specification Symbol Description 02 Rc1/4 N02 NPT1/4 F02 G1/4*1 T Calibration certificate Option 2 Symbol Description Nil None *1 ISO 1179-1 compliant Output specification*1 A Bracket A (Interchangeable with
In cases where it is not practical to change the vacuum pump, install a capacity tank (volume depending on the operating conditions) on the VAC side. y The vacuum pressure response time after a change in the input signal is influenced by the internal volume on the setting side (including piping).
Able to control and set a constant speed easily. Retainer prevents accidental loss of needle.